Home
  By Author [ A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z |  Other Symbols ]
  By Title [ A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z |  Other Symbols ]
  By Language
all Classics books content using ISYS

Download this book: [ ASCII | HTML | PDF ]

Look for this book on Amazon


We have new books nearly every day.
If you would like a news letter once a week or once a month
fill out this form and we will give you a summary of the books for that week or month by email.

Title: The Traveling Engineers' Association - To Improve The Locomotive Engine Service of American Railroads
Author: Anonymous
Language: English
As this book started as an ASCII text book there are no pictures available.


*** Start of this LibraryBlog Digital Book "The Traveling Engineers' Association - To Improve The Locomotive Engine Service of American Railroads" ***


THE
TRAVELING ENGINEERS'
ASSOCIATION


To Improve The Locomotive
Engine Service
of American Railroads


EXAMINATION QUESTIONS AND ANSWERS


For Firemen for Promotion
and New Men for Employment   :-:


Copyrighted by W. O. Thompson, March, 1911
Revised January, 1919

       *       *       *       *       *



=PREFACE=


It is the policy of railroads to employ firemen who will in time become
competent locomotive engineers. This requires that a man should have at
least a common school education, good habits and be in good physical
condition. He should be alert, with good reasoning faculties and a man
of sound judgment. Having these qualifications, advancement will come to
those who are conscientious in discharging their duties and who devote
some of their leisure hours to study.

As an aid to this end, and that the railroad companies may derive the
highest efficiency from the man employed as a locomotive engineman, a
code of questions is given him, and it is expected that the preparation
necessary to correctly answer the questions will indicate how well he
has progressed.

The list of questions is also intended as a guide to the matters on
which he should be correctly informed, both during his term of service
as a fireman and for future promotion to engineer.

When a man is first employed as a fireman he will be given a list of
questions on which he will be examined at the end of the first year;
having passed this examination successfully he will then be given the
examination questions for the following year; having passed this
examination satisfactorily, he will be given a third and final set of
examination questions on which he will be examined before being promoted
to engineer. All these examinations will be both written and oral. The
third year examination for promotion will be before the General Board of
Examiners. At any of these examinations, if he fails to pass 80 per
cent. of the questions asked, another trial, not less than two months
and not more than six months later, will be given him to pass the same
examination; if he fails to pass by a percentage of 80 per cent. he
shall be dropped from the service.

Where the examinations consist of both air brake and machinery, the
candidate must pass 80 per cent. in each to be successful.

Firemen passing the third and final series of questions will be promoted
in the order of their seniority as firemen, except that those who pass
on the first trials shall rank, when promoted, above those who passed on
the second trials.

Engineers employed who have had service on other roads, will be required
to pass the third series of questions before entering the service.

It is not expected that the man will pass these examinations without
assistance, and in order that he will understand the use of locomotive
and air brake appliances properly, he is expected to go to the Master
Mechanic, General Foreman, Road Foreman or Traveling Engineer, also Air
Brake Inspector or Instructor, or any other official, and ask them for
such information as may be required on any of the questions or on any
points in connection with the work. He is not only invited, but also
urged to do this, as the more knowledge of his business a man possesses,
the better will be the results obtained. He will have ample time to
study each set of questions; there is no doubt that with a reasonable
amount of study each week, supplemented with close observation of the
working of the locomotive, the information necessary to answer
satisfactorily the entire list of questions can be easily mastered in
the time given. In regard to breakdowns, it is advised that he carefully
inspect each breakdown or disabled engine that comes to his notice, see
where the parts have given way and in what manner the work of blocking
up it done. It is not expected that all the breakdowns which may happen
to a locomotive will occur on the engine that he is with; therefore it
is good practice to observe how other men care for these breakdowns. In
connection with these examinations the work done by the fireman during
the year and how the work compares with that of other firemen in the
same class of service will be carefully noted; his record as to the use
of coal, supplies and attention to duty will be taken into
consideration.

It is hoped that he will give everything in detail the consideration it
merits and realize fully that it is by looking after the little things
that a man succeeds. It should be borne in mind that by filling well the
position he holds he becomes entitled to the confidence that makes
better positions possible. It is understood that those who conduct the
examination may ask any question or questions bearing on any subject of
this examination, in order to determine how well the persons being
examined understands the subject. A mere memorized answer will not be
sufficient. The full meaning of each answer must be understood.



=EXAMINATION QUESTIONS=

FIRST SERIES


1. Q. What do you consider essential for your success in regard to the
use of fuel A. I deem it essential to my success to be as economical in
the use of fuel and supplies as is consistent with the work to be
performed, exercising good judgment in my work, harmonious co-operation
with my engineer, and showing a willingness to learn and practice the
best methods in my work.

2. Q. What are the fireman's duties on arrival at enginehouse previous
to going out on a locomotive?

A. He is required to examine the bulletin board, guards on water and
lubricator glasses; try gauge cocks to find true water level; then
examine grates, ash-pan, flues and fire-box. Put fire in proper shape;
see that a proper supply of firing tools, water, coal, oil and waste are
provided, that all lamps and markers are filled, cleaned and in proper
condition; and to perform such other duties as may be required by the
engineer to assist him in getting the engine in readiness.

3. Q. What pressure is indicated by the steam gauge? What is meant by
atmospheric pressure?

A. The pressure per square inch inside of the boiler. Atmospheric
pressure is the pressure represented by the density of the atmosphere in
pounds per square inch, which is at sea level 14.7 pounds.

4. Q. On what principle does a steam gauge work?

A. The steam gauge pointer is actuated by a flattened or bent round tube
to straighten itself under the pressure of steam against the water
inside of tube. The gauge pointer receives movement from suitable
mechanism connected with the tube.

5. Q. What is the source of power in a steam locomotive?

A. Heat is the source of power in all steam engines. It is necessary to
have fuel and water. When fuel is burned, the water coming in contact
with the hot sheets evaporates and becomes steam, which is then used in
the cylinders to force the pistons back and forth.

6. Q. About what quantity of water should be evaporated in a locomotive
boiler to the pound of coal?

A. From five to seven pounds of water. For example, one gallon of water
weighs eight and one-third pounds, therefore 100 pounds of coal should
evaporate from sixty to eighty-four gallons of water.

7. Q. What is steam, and how is it generated?

A. Steam is water in the condition of a vapor and is generated by
heating the water above the boiling point.

8. Q. What is the purpose of the water gauge glass and gauge cocks?

A. To indicate the level of water in the boiler.

9. Q. What would indicate to you that the boiler connections of water
gauge glasses were becoming clogged?

A. The up and down movement of the water in the glass would become slow
and inactive, or it would not register correctly with the gauge cocks.

10. Q. At what temperature does water boil?

A. At atmospheric pressure, which is 14.7 pounds at sea level, water
boils at 212 degrees Fahrenheit; the temperature, however, increases as
the pressure under which the water is boiled increases. At 200 pounds
boiler pressure the temperature would be 388 degrees Fahrenheit.

11. Q. What is carbon?

A. Carbon forms the greatest part of all kinds of coal; the higher the
per cent. of carbon, the higher the grade of coal.

12. Q. What is the composition of bituminous coal?

A. It is composed of carbon about 75 per cent. and many gaseous
substances, as is shown by its burning with a large flame and much
smoke. Anthracite, on the contrary, is nearly pure carbon and burns with
a small flame.

13. Q. What is combustion?

A. Combustion or burning is a chemical process, it is the action of fire
on inflammable substances and is the union of the oxygen in the air with
the carbon in the fuel; this is called rapid combustion. Slow combustion
is the decaying of wood or iron by the elements.

14. Q. Is air necessary for combustion?

A. Yes.

15. Q. About how many cubic feet of air is necessary for the combustion
of a pound of coal in a locomotive fire-box?

A. About 300 cubic feet of air must pass through the grates and fire
for complete combustion of one pound of coal.

16. Q. Why must air be heated before combining with coal?

A. Air, like coal and its gases, must be heated before they will unite
to form what is known as combustion and so as not to reduce the
temperature of the fire-box below the igniting point of the gases.

17. Q. Why is it necessary to provide for combustion a supply of air
through the fuel in the furnace?

A. In order to supply the oxygen necessary for combustion.

18. Q. What is the effect upon combustion if too little air is supplied?
If too much air is supplied?

A. If too little air is supplied, combustion is not complete, and only
one-third as much heat is obtained. If too much air is supplied,
combustion is complete; but the excess air must be heated, resulting in
a lower temperature. If twice the amount of air required for complete
combustion be supplied, the temperature of the fire-box will be about
one-half as high.

19. Q. Give a practical definition of the igniting temperature.

A. In all ordinary combustion there is a definite temperature, called
the ignition or kindling temperature, to which combustible substance
must be heated in order that it may unite with the gas in supporting the
combustion. The burning substance must not only be heated up to the
kindling temperature, but it must be kept as high as this temperature,
or combustion will cease.

20. Q. State why such temperature is necessary and at what place in the
fire-box it is most required.

A. The center is the hottest part of the fire-box. There is a much lower
temperature in the fire-box at the sides and end sheets, due to the
water on the opposite sides of the sheets being of a lower temperature
than the fire-box; therefore if we get as high a temperature as possible
at the side and end sheets, we will increase the steam-making efficiency
of the boiler. The gases which are liberated from the coal as soon as it
becomes heated must attain a temperature of about 1,800 degrees
Fahrenheit, known as the "temperature of ignition," before they will
unite with air which must also be heated up to that point.

21. Q. How is draft created through the fire?

A. Exhaust steam escaping through the stack reduces the pressure in the
smoke-box below the pressure of the atmosphere outside, therefore the
air tends to force itself into the smoke-box through all openings; with
everything in good condition, the easiest and largest passage for it is
through the grates and other openings into the fire-box and from it
through the tubes into the smoke-box and up the stack.

22. Q. Is smokeless firing practicable?

A. Yes, but it is necessary in order to obtain good results that boiler
and fire-box be in good condition, coal broken to the proper firing
size; then, with the hearty and intelligent co-operation of both
engineer and fireman, smokeless firing is both economical and
practicable.

23. Q. In what condition should the fire be in order that the best
results may be obtained from the combustion of the coal?

A. The fire should be as light as the work being done by the engine will
permit, evenly distributed over the grates and free from clinkers.

24. Q. How should the blower be used?

A. A blower should be used very lightly, being careful not to draw too
much air into the fire-box and through the flues, especially when fire
is being cleaned or thin on grates.

25. Q. What is the result of opening the fire-door when the engine is
working steam?

A. It will cause a cooling effect in the fire-box and is liable to start
the flues leaking.

26. Q. What is the effect of putting too many scoops of coal on a bright
fire? Is this a waste of fuel?

A. It has the effect of temporarily deadening and cooling the fire,
causes emission of quantities of black smoke, as only a limited amount
of gas can be burned in a fire-box at a time; all in excess of that
amount escapes from the stack and is a waste of fuel.

27. Q. What effect has the fire upon a scoopful of coal when it is
placed in the fire-box?

A. The heat from the fire drives the gases from the coal and they are
ignited by the hot flame as they pass over the bright fire; the coke
which is left burns where it is.

28. Q. In what condition should the fire be to consume these gases?

A. A bright white coke fire, almost incandescent.

29. Q. What is the temperature of the fire when in this condition?

A. It must not be less than 1,800 degrees Fahrenheit to consume the
gases liberated from the coal, and it only requires from 750 to 900
degrees Fahrenheit to burn the coke that remains on the grate; as coke
burns from the outside, less heat is required to consume it.

30. Q. How can the fire be maintained in this condition?

A. By adding coal to the fire in small quantities, spreading it over the
grate surface and no faster than it is burned.

31. Q. What is black smoke? Is it combustible?

A. Black smoke consists of small particles of carbon suspended in the
gases of combustion and indicates incomplete combustion. Black smoke is
not combustible, it is like lampblack and cannot be burned after having
been produced. The production of it can be prevented by suitable
arrangements and manipulation.

32. Q. Should the gas not burn in the fire-box, will it burn after it
enters the flues? Why?

A. Gas will not burn only a short distance in the flues of a boiler, as
the water absorbs the heat so quickly that the temperature of gas is
lowered below the igniting point.

33. Q. What is the effect on the flow of air through the fire from
opening the door? What on the burning of the gases? What on the flues
and sheets of the fire-box?

A. When the furnace door is opened, the flow of air through the grate is
stopped in proportion to the amount that passes through the door. The
vacuum will be filled from the quickest source and the door is closer
than some parts of the grate. The gases mix with the air from the door
and pass out through the flues; no combustion takes place, as the air
is not hot enough to unite with the gas. The flues and sheets of the box
will be caused to leak on account of the rapid contraction.

34. Q. Can the firing be done more effectively if the water level is
observed closely?

A. Yes, in order to know how much water there is in the boiler and
whether it is necessary to hurry the fire; if the boiler is full, it is
possible to prevent the pops opening by delaying the fire.

35. Q. How should the fire and water be handled in starting from a
terminal or other station?

A. The steam pressure should be near the maximum and there should be
sufficient water in the boiler to last until such time as the fire is
burning well so that the pressure will not be reduced when water is put
into the boiler. There should be a moderately heavy bed of fire well
burned and distributed evenly over the grates. After the fire is burning
well, the injector should be started lightly; the feed being gradually
increased so as not to cause any decrease of steam pressure.

36. Q. What is the purpose of a safety valve on a locomotive boiler? Why
are more than one used?

A. A safety valve is used to limit the maximum pressure in the boiler by
opening and allowing steam to escape. More than one safety valve are
used as additional protection against excessive pressure; one is set at
the maximum pressure and the others are set at two or three pounds above
the maximum pressure.

37. Q. What is usually the reason for steam being wasted from the safety
valve? What can be done to prevent this waste?

A. Careless firing, careless running. Both engineer and fireman work in
harmony to obtain the best results.

38. Q. What is the estimated waste of coal for each minute the safety
valve is open?

A. About fifteen pounds. The estimated waste of steam when an engine
pops equals every second all the heat obtained from a quarter pound of
coal. Safety valves usually remain open about half a minute, resulting
in the loss of about eight pounds of coal.

39. Q. What should be the condition of the fire on arriving at a station
where a stop is to be made?

A. On approaching the station where a stop is to be made, firing should
be stopped far enough back to allow the carbon gases to be consumed
before the throttle is closed, so there will be little or no black smoke
from the stack and yet have sufficient fire that it will not be
necessary to feed the fire again if a short stop is to be made until the
train is started and the engine cut back or nearly to the running
cut-off.

40. Q. How should you build up the fire when at stations in order to
avoid black smoke?

A. Put in small quantities of coal at a time, have the door slightly
open and have the blower on lightly; good judgment must be exercised by
the fireman.

41. Q. Why is it that if there is a thin fire with a hole in it the
steam pressure will fall at once?

A. Because too much cold air is drawn into the fire-box and through the
tubes, retarding combustion and cooling the fire-box and tubes.

42. Q. If the injector is to be used after throttle is shut off, how
should the fire be maintained?

A. A sufficient quantity of coal should be placed on the grates to
maintain the maximum steam pressure and the blower used to keep the fire
burning brightly.

43. Q. What would be the result of starting a heavy train or allowing
drivers to slip with the fire too thin on the grates?

A. The fire would be pulled off the grates and into the tubes, leaving
the fire bed full of holes and some of the fire remaining on the grates
turned over. Large quantities of cold air would be drawn in, resulting
in a rapid decrease of temperature and pressure. The tubes would
possibly start leaking and the fire would be in such condition that it
could not be built up properly in a long distance. Possibly the grates
would become clogged up with green coal--an excellent opportunity for
forming clinkers. In this condition, the engine would fail to make steam
for the entire trip.

44. Q. Where should the coal, as a rule, be placed in the fire-box?

A. As a rule, more coal is burned along the sides and in the corners
than in the middle of the grates; the fire should consequently be kept
somewhat heavier along the sides and corners than in the middle.

45. Q. How is the fire affected by and what causes clinkers?

A. A clinker shuts off area of grate surface according to its size, and
thereby shutting off that much of the air supply and interfering with
proper combustion. Clinkers are caused by firing too heavy in spots,
which prevents sufficient air passing up through these spots and allows
the coal to run together, melting the ash, and sand; running a hoe or
slash bar through the fire will bring the points of melted sand
together, thereby causing a clinker.

46. Q. How can you best avoid their formation and dispose of them?

A. Light firing and occasionally moving the grates lightly is the best
preventive. When once formed, they should be removed if possible by
firing around and burning them out.

47. Q. How can you explain the slower burning of the coke and how
understand the proper manner of supplying fresh coal?

A. The gases of coal are lighter than air and will pass away whether
consumed or not. The slow burning of the coke is due to the fact that it
burns from the outside only. When a fire reaches a white or incandescent
heat it indicates that the gases are burned and a fresh supply of coal
should be added; this is to be done as light as the service performed by
the engine will permit.

48. Q. When and for what purpose is the use of a rake on the fire bed
allowable?

A. The rake should be used on the fire very seldom, because raking the
fire bed tends to form clinkers, especially when the rake is plunged
down through the fire to the grate. It may be used when necessary to
rake the fire lightly when on the road for the purpose of breaking the
crust, which may be found as a consequence of too heavy firing.

49. Q. Within what limits may steam pressure be allowed to vary, and
why?

A. Pressure should not be allowed to vary more than five pounds from the
maximum for the reason that too much expansion and contraction will
take place, which many times is the cause of flues leaking, cracked or
broken side sheets and stay bolts.

50. Q. Has improper firing any tendency to cause the tubes to leak? How?

A. Yes; if the pressure is not regularly maintained, the fluctuations of
temperature cause constant contraction and expansion to take place. If
the fire is not carried level, but is carried heavy in some parts of the
fire-box and light in others, holes will be worked in, cold air drawn
through, lowering the temperature, chilling the tubes and causing leaks.
Carrying the fire too heavy in some places, causes clinkers to form. If
the door is open too long, too much cold air is drawn over the fire,
causing the tubes to leak.

51. Q. What do you consider abuse of a boiler?

A. Careless or improperly supplying water to the boiler, improper firing
or allowing steam to vary from high to low pressure, causing unnecessary
expansion and contraction.

52. Q. Does the stopping up of flues affect the steaming capacity of the
engine?

A. Yes; obstructed flues reduce the heating surface, reduce the steaming
capacity of the engine, and, as a rule, result in causing the flues to
leak. They also cause an increase of speed of the gases through the
remaining flues and a poor steaming engine.

53. Q. What causes honeycomb over the flues?

A. Honeycomb on flues is usually caused by the draft through the fire
picking up the sulphur and molten clay which is in a molten and sticky
condition in the fire; as it passes on its way to the stack, some of it
strikes the flue-sheet and sticks or passes through the flues, clogging
up the netting in the front end.

54. Q. How would you take care of a boiler with leaky tubes or fire-box,
and why?

A. Keep a bright, clean fire, especially up next to the flue-sheet, and
as even a pressure of steam as possible and not use the blower any
stronger than is absolutely necessary.

55. Q. Why is it very important that coal should be broken so that it
will not be larger than an ordinary sized apple before being put into
the fire-box?

A. In order to get rapid and complete combustion, coal should be broken
into small pieces; this aids combustion by exposing a larger surface to
the flame and can be fired more economically and better results are
obtained.

56. Q. Should rapid firing be practiced?

A. No; it should not be practiced for the same reason that heavy firing
is wrong. A few moments should intervene between each shovelful to allow
the fresh coal to get to burning and to maintain the high temperature in
the fire-box.

57. Q. When and why should you wet the coal on the tender?

A. Coal should be wet for the purpose of cleanliness to keep dust from
flying and because moderately wet coal gives out more heat for the
reason that there is not so much fine coal drawn through the tubes. It
should be wet as often as necessary to accomplish these purposes.

58. Q. What are the advantages of a large grate surface?

A. Greater heating surface, lighter fire and more complete combustion
are possible with the larger grate surface, because a larger amount is
burning at one time at a slower rate of combustion.

59. Q. Why are grates made to shake, and how, when and where should they
be shaken?

A. For the purpose of breaking any clinkers that might form and to shake
out all refuse from the grates. The best time to shake grates is when
throttle is closed, as there is no exhaust to carry the unconsumed gases
and sulphur through the flues into the front end, which is liable to
choke or clog up netting and cause a steam failure. Grates should not be
shaken while passing over bridges, near lumber or hay yards or through
prohibited territory.

60. Q. Do you understand that coal furnished represents money invested,
and should be fired economically and not allowed to fall out of the
gangway?

A. The fuel of locomotives is property and represents money invested the
same as do buildings, rolling stock, etc.; careless or inefficient
firemen who waste fuel destroy property as certainly as though cars or
engines were smashed up. The coal should be carefully raked off the deck
and in from the gangways; it should not be allowed to fall, as it is
wasted and dangerous to people near the track. The deck should be kept
clean for greater comfort and convenience.

61. Q. Is is objectionable to fill the tanks too full of coal or
overflow tank at standpipes or water tanks?

A. It is. Tanks filled too full of coal are dangerous and a great waste
of coal, as the jar when running will cause a part of it to fall off;
water overflowing from tanks results in washing away the ballast and in
cold weather freezes over the tracks.

62. Q. What are the duties of a fireman on arrival at the terminal?

A. Different roads have different assigned duties for the firemen to
perform. They should leave the cab, boiler head, oil cans and deck in a
clean condition, boiler full of water, enough fire and steam, so that
the hostler will not be required to put in fuel while the engine is in
his charge; should know that throttle valve is securely closed, reverse
lever in center of quadrant, cylinder cocks open, and if equipped with
independent brake, it to be applied; in fact, it is an excellent
opportunity for a mechanical officer to judge the ability of the fireman
and future engineer.

63. Q. Is the engineer responsible for the fireman's conduct while on
duty and for the manner in which the fireman's duties are performed?

A. He is. The fireman is under the direction of the engineer, and the
fireman's duties are to be performed in accordance with the engineer's
instructions.

64. Q. What is the duty of the superheater damper, and how does it
operate?

A. The duty of the damper is to control the flow of gases through the
large flues, thereby protecting the units which are contained therein
from being overheated after throttle is closed. The position of damper
when the engine is not working steam, is closed.

65. Q. What will be the effect on the steaming of the engine if the
damper does not open properly?

A. Engine will steam poorly for the reason that there will be no draft
through the large flues. The steam will not be superheated because
heated gases cannot come in contact with superheated units contained in
the large flues.

66. Q. How may steam failure be avoided in case the damper fails to
operate?

A. The counterweight may be tied up, thereby opening the damper.



=AIR BRAKE QUESTIONS=


1. Q. What is an air brake?

A. A brake operated by compressed air.

2. Q. How is this air compressed?

A. By an air compressor on the locomotive.

3. Q. Name the different parts of the air brake as applied to the
locomotive.

A. The air compressor, compressor governor, automatic and independent
brake valves, distributing valve, triple valve, auxiliary reservoir,
brake cylinders, main reservoir, air gauges, angle cocks, cut-out cocks
and the necessary piping.

4. Q. What is the purpose of the main reservoir?

A. It is used for storing a large volume of air for the purpose of
promptly charging and recharging the brakes. Where the engine is
equipped with either the E. T. or L. T. type of brakes, main reservoir
air is used to supply the air to the brake cylinders on the locomotive.

5. Q. What other appliances use main reservoir air?

A. It is used in the operation of the power reverse gear, sand blower,
bell ringer, water scoop, air signal, fire door, water sprinkler and
other devices.

6. Q. What does the red hand on each of the air gauges indicate?

A. The red hand on the large gauge indicates main reservoir pressure; on
the small gauge, brake cylinder pressure.

7. Q. What does the black hand on each of the air gauges indicate?

A. The black hand on the large gauge indicates the equalizing reservoir
pressure; on the small gauge, brake pipe pressure.

8. Q. What pressure is usually carried in the main reservoir?

A. Ninety pounds in freight and 130 pounds in passenger service. But
where freight engines are equipped with duplex compressor governor, the
low pressure top is adjusted to ninety pounds and the high pressure top
to 130 pounds.

9. Q. What pressure is usually carried in the brake pipe?

A. Seventy pounds in freight and 110 pounds in passenger service.

10. Q. What must the air pass through in flowing from the main reservoir
to the brake pipe?

A. Through the automatic brake valve.

11. Q. Name the different positions of the automatic brake valve.

A. Release, running, lap, service and emergency positions. The brake
valve used with the E. T. and L. T. equipment has still another position
known as holding position, which is located between running and lap
positions.

12. Q. Name the different positions of the independent brake valve.

A. Release, running, lap, slow application and quick application
positions.

13. Q. How many kinds of triple valves are there in use?

A. Two; plain and quick action.

14. Q. How is the automatic brake applied? How released?

A. The automatic brake is applied by a reduction of brake pipe pressure,
and is released by restoring the brake pipe pressure.

15. Q. When the independent brake valve handle is placed in application
position, are the train brakes affected?

A. No; only the brakes on the locomotive are applied.

16. Q. What controls the pressure in the main reservoir?

A. The compressor governor.



=EXAMINATION QUESTIONS=

SECOND SERIES


1. Q. What, in your opinion, is the best way to fire a locomotive?

A. To carry a nice, level fire on the grate, or it may be just a little
heavier at the sides and front, so the air cannot come through it near
the sheets as rapidly as in the center of the fire-box; always fire as
light as consistent with the work required, endeavor to maintain a
uniform steam pressure at all times, and avoid unnecessary black smoke
and a waste of steam through the safety valves by the engine popping.

2. Q. What are the advantages of superheated steam over saturated steam
in locomotive service?

A. Saving in water; saving in fuel; increased boiler capacity and a more
powerful locomotive. Superheated steam does away entirely with all
condensation in the cylinders, while saturated steam coming in contact
with passages in cylinder saddle and walls of cylinders, is immediately
cooled and in cooling, a part of it is changed back into water which
affects the pressure and therefore its capacity to do work.

3. Q. How is the saving in water produced?

A. By the elimination of all cylinder condensation present in saturated
steam locomotives and the increase in volume of a given weight of steam.

4. Q. How is the saving in coal accomplished?

A. Because there is less steam used to do the same amount of work, there
is less water evaporated and consequently less coal required to
evaporate the water.

5. Q. How is the increased boiler capacity obtained?

A. A boiler will evaporate a certain amount of water into steam and if
part of the steam is lost by condensation, only that remaining is
available for running the engine. Superheating eliminates the losses,
thereby increasing the available useful steam. Further, superheating
increases the volume of a given weight of steam, thereby reducing the
consumption of steam required to develop a certain power and
consequently increases the capacity.

6. Q. How is a more powerful engine obtained?

A. By reason of the increased boiler capacity an engine may be worked
farther down before a steam failure occurs.

7. Q. What type of fire tube superheater is in most general use in
locomotive service?

A. The top header fire tube type, known as the "Schmidt Superheater." A
system of units located in large flues through which the steam passes on
its way from the dry pipe to the steam pipes, and a damper mechanism
which controls the flow of gases through the large flues.

8. Q. Describe the construction and location of the header.

A. The header is a simple casting, divided by partition walls into
saturated and superheated steam passages. It is located between the dry
pipe and the steam pipes, the same as the nigger head in a saturated
locomotive. The dry pipe is in communication with the saturated steam
passages and the steam pipes with the superheated steam passages and
these are in communication with each other through the superheated
units.

9. Q. Describe the construction of superheater units and their
connection to the header.

A. The units are composed of four seamless steel pipes, connected by
three return bends. Of the four pipes, two are straight and two are bent
upward and connected to the header by means of a clamp and bolt; one end
of the unit is in communication with the saturated steam passage and the
other with the superheated steam passage in the header casting.

10. Q. Trace the flow of steam through the top header fire tube
superheater.

A. When the engine throttle is open, saturated steam passes through the
dry pipe into the saturated steam passage of the header casting. From
this passage it enters one end of the unit, passing backward toward the
fire-box, forward through one of the straight pipes and the front return
bend, backward through the other straight pipe to the back return bend,
and forward through the bent pipe and upward into the superheater steam
passage of the header, from which it enters the steam pipes and is
carried to the steam chest.

11. Q. What should be the position of throttle valve when running a
superheater locomotive?

A. The engine should always be run with as wide open throttle as the
conditions will permit, regulating the steam admission to the cylinders
according to work to be performed.

12. Q. What should be the position of throttle while drifting?

A. The throttle valve should be kept slightly open while drifting, so as
to admit a small quantity of steam in valve chamber and cylinder above
atmospheric pressure, to prevent the inrush of hot air and gases which
destroy lubrication, also to prevent excessive wear to valve, cylinder
and piston rod packing.

13. Q. How should the water be carried in boiler of superheater
locomotives?

A. As low as the conditions will permit, because this practice reduces
the tendency to work water over into the dry pipe and units, as the
superheater locomotive will use one-third less water than the saturated
locomotive.

14. Q. What care should be exercised in lubricating a superheater
locomotive?

A. The supply of oil to steam chest should be watched very closely by
the engineer, he to know that lubricator is feeding constantly and
evenly over entire division, and according to work performed.

15. Q. Describe the general form of a locomotive boiler.

A. A locomotive boiler is cylindrical in form, it usually has a
rectangular shaped fire-box at one end and a smoke-box at the other, and
flues extend through the cylindrical part, and, like the fire-box, are
surrounded by water.

16. Q. How does the wide fire-box type of boiler differ from the
ordinary boiler, and what are its advantages?

A. The wide fire-box type of boiler is built so the fire-box is above
the frame and extends out over the driving wheels. The advantages of
this are to obtain a larger grate area in the same length of fire-box
and to give a slower rate of combustion per square foot of grate
surface. The deep fire-box is limited in width to the distance between
the frames, while the shallow fire-box sets on top of the frames and
between the driving wheels.

17. Q. Why have two fire-box doors been placed in the large type of
locomotive boilers?

A. For convenience of the fireman on account of the greater width of the
fire-box, so that coal can easily be distributed to all parts of the
fire-box.

18. Q. Describe a locomotive fire-box.

A. The modern form is a rectangular shaped structure located at the back
end of the boiler. It has a door and is composed of two side sheets, a
crown sheet, a back sheet and a flue sheet from which the flues extend
to the smoke-box at the other end of the boiler.

19. Q. To what strains is a fire-box subjected?

A. To crushing strains and to those of unequal contraction and
expansion.

20. Q. How are the sheets of a fire-box supported?

A. They are supported by staybolts screwed through the inside and
outside sheets with their ends riveted over.

21. Q. In what manner is a crown sheet supported?

A. By crown bars or radial staybolts.

22. Q. What are the bad features about crown bars?

A. They are hard to keep clean and frequently cause crown sheets to
become mud burned.

23. Q. What are the advantages of radial stayed crown sheets?

A. They are easier to keep clean and cheaper to repair.

24. Q. How are the inside and outside sheets of a fire-box secured at
the bottom?

A. They are riveted to a wrought iron ring called a mud-ring.

25. Q. Describe the ash-pan and its use.

A. It is a receptacle secured to the fire-box and usually provided with
dampers to regulate the flow of air to the fire. It collects the ashes
that drop from the fire-box and prevents them from setting fire to
bridges or other property along the track. Engine-men must know that
ash-pan slide and hopper bottoms are closed before leaving enginehouse.

26. Q. What is a "wagon-top" boiler?

A. It is a boiler that has the fire-box end made larger than the
cylindrical part to provide more steam space.

27. Q. Why are boilers provided with steam domes?

A. To furnish more steam space and to obtain dryer steam and to provide
a place for the safety valves, steam pipes, throttle valve and whistle.

28. Q. What must be the condition of a boiler to give the best results?

A. It must have good circulation and be clean and free from mud or
scale.

29. Q. What is meant by "circulation" in a boiler?

A. Free movement of the water, so that it may come in contact with the
heating surface and after being converted into steam be immediately
replaced by a fresh supply of water.

30. Q. What would be the effect if a "leg" of the fire-box became filled
with mud?

A. There would be no water in contact with the fire-box sheets and they
would quickly become overheated and mud-burned.

31. Q. What would be the result if the fire-box sheets became
overheated?

A. They would be weakened and forced off the staybolts and an explosion
would occur.

32. Q. Would it be advisable to put water into a boiler after the sheets
had become bare and red hot?

A. No. The fire should be killed at once.

33. Q. What effect has the stoppage of a large number of flues?

A. The heating surface and draft are decreased by just that much area.

34. Q. Why are boiler checks placed so far away from the fire-box?

A. To introduce the water into the boiler at as great a distance from
the fire-box as possible. This permits the water to become heated to a
high temperature before it comes in contact with the fire-box and also
improves circulation.

35. Q. What part of the boiler has the greatest pressure? Why?

A. The bottom, because it is subject to the weight of the water in
addition to the steam pressure in the boiler.

36. Q. What are the advantages of the extension front end?

A. To provide room for suitable draft and spark appliances.

37. Q. What is the purpose of a netting in a smoke-box or front end?

A. To act as a crusher of all cinders and prevent large cinders from
passing out of the front end to the atmosphere.

38. Q. What is the object of hollow staybolts?

A. To indicate when the staybolt is broken by the escape of steam
through the small hole in the bolt.

39. Q. What will cause the engine to tear holes in the fire?

A. Working hard or slipping when the dampers are open and the door
closed, or too thin a fire.

40. Q. Name the various adjustable appliances in the front end by which
the draft may be regulated.

A. The exhaust nozzle, the diaphragm and the draft pipes or petticoat
pipe.

41. Q. What object is there in having the exhaust steam go through the
stack?

A. To create a draft through the tubes and fire-box.

42. Q. How does this affect the fire?

A. The exhaust steam escaping through the stack tends to empty the
smoke-box of gases and produces a partial vacuum there, atmospheric
pressure then forces air through the grates and tubes to refill the
smoke-box, and in this way the draft through the fire is established and
maintained.

43. Q. Explain what adjustments can be made and the effect of each
adjustment on the fire.

A. Larger or smaller nozzle tips cause less or greater draft on the
fire; raising or lowering the draft pipes and diaphragm causes the
engine to burn the fire more at the rear or front end of the fire-box;
the size and position of the draft pipes increase the draft through the
top or bottom flues; the latter adjustments should always be attempted
before reducing the nozzle.

44. Q. What does it indicate when the exhaust issues strongest from one
side of the stack?

A. The stack, exhaust pipe or petticoat pipe are out of plumb.

45. Q. What is the effect of leaky steam pipe joints inside the
smoke-box?

A. The engine will not steam freely.

46. Q. What causes "pull" on the fire-box door?

A. The partial vacuum in the front end; when excessive it indicates
dampers closed, fire clinkered or insufficient opening for the admission
of air under the fire.

47. Q. If upon opening the fire-box door you discover there what is
commonly called a red fire, what might be the cause?

A. The grates may have become clogged with ashes or clinkers so that
sufficient air could not pass through them to the fire.

48. Q. Is it not a waste of fuel to open the fire-box door to prevent
pops from opening? How can this be prevented more economically?

A. Yes. This can usually be prevented by putting the heater into the
tank, or putting on the injector, or by more careful firing.

49. Q. Describe the principle upon which the injector works.

A. The action of the injector is due first to the difference between
"kinetic" or moving energy and "static" or standing energy; second, to
the fact that steam at a pressure travels at a very high velocity and
when placed in contact with a stream of water it is condensed into
water, and at the same time it imparts enough velocity to the water to
give it sufficient momentum to overcome a pressure even greater than the
original pressure of the steam. By imparting this velocity to the water
it gives it sufficient energy to throw open the check valves and enter
the boiler against high pressure.

50. Q. What is the difference between a lifting and a non-lifting
injector?

A. A lifting injector will create sufficient vacuum to raise the water
from the level of the tank. The steam tubes in a non-lifting injector
are different and it will not raise the water, but merely force it into
the boiler. A non-lifting injector must be placed below the level of the
water in the tank so the water will flow to it by gravity.

51. Q. Will an injector work with a leak between the injector and tank?
Why? Will it prime?

A. A lifting injector will not work if the leak is bad. It will not
prime because the air admitted through the leak destroys the vacuum
necessary to raise the water to the injector level. A non-lifting
injector will work, as the water will escape from the pipe instead of
air being drawn into it as with the lifting injector.

52. Q. If it primes well, but breaks when the steam is turned on wide,
where would you look for the trouble?

A. Insufficient water supply due to tank valve partly closed, strainer
stopped up or tank hose kinked, injector tubes out of line, limed up, or
delivery tube cut, or wet steam from the throttle.

53. Q. If it would not prime, where would you expect to find the
trouble?

A. Insufficient water supply, priming valve out of order, or with the
lifting injector the trouble might be caused by a leak between the
injector and tank.

54. Q. Will an injector prime if the boiler check leaks badly or if it
is stuck up? If the injector throttle leaks badly?

A. No.

55. Q. If steam or water shows at the overflow pipe when the injector is
not working, how can you tell whether it comes from the boiler check or
the injector throttle?

A. Close the main steam valve at the boiler, that will stop the leak if
it comes from the injector throttle.

56. Q. Will an injector prime if primer valve leaks? Will that prevent
its working?

A. It will prime, but not as readily as with priming valve in good
condition. This will not prevent its working, but it may waste some
water from the overflow.

57. Q. Will an injector work if air cannot get into the tank as fast as
the water is taken out?

A. No.

58. Q. If you had to take down a tank hose, how would you stop the water
from flowing out of the tank that has the syphon connections instead of
the old-style tank valves?

A. Open the pet cock at the top of the syphon before taking the hose
down.

59. Q. Is any more water used when the engine foams than when the water
is solid?

A. Yes, very much more.

60. Q. How would you prevent injector feed pipes or tank hose from
freezing in winter when not in use?

A. The steam valve should be slightly open to permit a slight
circulation of steam through the feed and branch pipes. The heater cock
should be closed and the drip cock under the boiler check or on the
branch pipe should be opened to insure a circulation of steam through
the branch pipe.

61. Q. How would you prevent the overflow pipe from freezing with a
lifting injector?

A. The overflow valve should be opened just enough to permit a little
steam to escape through the overflow pipe to prevent it from freezing.

62. Q. Name the various parts of the injector.

A. The injector consists of a body supplied with a steam valve, a steam
nozzle, a primer, a combining tube, a delivery tube, a line check valve,
an overflow valve, a water valve, and a lifting injector has a lifting
tube.

63. Q. What may be done if a combining tube is obstructed?

A. The steam valve bonnet may be removed and the obstruction forced out
with a piece of stiff wire, or uncouple the delivery pipe from the
injector and unscrew and remove the tubes; the obstruction can then be
removed and the tubes replaced.

64. Q. How is the greatest injury done to a boiler when cleaning or
knocking the fire?

A. By excessive use of the blower drawing cold air through the fire-box
and flues.

65. Q. Why does putting a large quantity of cold water into a boiler
when the throttle is closed cause the flues to leak? When is this most
serious?

A. When steam is not being used there is not much circulation of water
in the boiler, and the water entering the boiler at about 150 degrees
temperature is heavier than the water in the boiler. The cooler water
will go to the bottom and reduce the temperature in that part of the
boiler and causing the flues to contract in length as well as in
diameter and this has a tendency to pull them out of the sheet. This
will loosen them and cause them to leak. After the fire has been knocked
this tendency is much greater, and for that reason cold water should not
be put into a boiler after the fire has been knocked out. Always fill
the boiler before the fire is knocked out.

66. Q. Is warm water in the tank of any advantage in making steam
rapidly?

A. Yes; careful experiments have shown that a locomotive will generate
one per cent. more steam for every eleven degrees that the tank water is
heated; thus by heating the feed water in the tank from 39 degrees to 94
would effect a saving of five per cent.

67. Q. Then why not heat the feed water to the boiling point (212
degrees)?

A. If the feed water is heated much above 100 degrees it will not
condense enough steam in the injector to cause it to work properly. Some
injectors will work hotter water than others. It would also spoil the
paint on the tank if heated to a much higher temperature.

68. Q. At 200 pounds pressure per square inch, what is the pressure per
square foot on the sheets of a boiler?

A. About fifteen tons.

69. Q. What is the total pressure on the fire-box of a large
locomotive?

A. Over 3,000 tons.

70. Q. Give a practical definition of heating surface.

A. The heating surface of a boiler includes all parts of the boiler and
tubes that are directly exposed to fire or heat from the fire and are
surrounded by water.

71. Q. Should an engine be slipped to get water out of the cylinders or
steam passages?

A. No; the water should be worked out by opening the cylinder cocks and
starting the engine slowly.

72. Q. What does it indicate when the smoke trails back over the train
and into the coaches after shutting off?

A. It indicates poor firing or a lack of understanding between the
engineer and fireman in regard to where the engine was to be shut off.

73. Q. Before shaking grates or dumping the ash-pan, what should be
observed?

A. That the engine is not passing over bridges or cattle guards,
crossings, switches, interlocking fixtures, or in yards. Fire on the
track should be extinguished promptly at places where ash-pans are
cleaned.

74. Q. Which is easier and more satisfactory on a long run, to stop and
clean the fire if necessary or to continue to the end of a long, hard
trip with a dirty fire?

A. Stop and clean the fire if necessary. It will save fuel and labor
during the remainder of the trip and may also save an engine failure.

75. Q. Should you examine the flues to see if they are stopped up and
leaking, and inspect the grate and grate rigging carefully before
leaving the engine at a terminal?

A. Yes, so they can be reported if necessary. Clean flues and grates
working well make a vast difference in the success of a fireman, and a
great many engine failures could be avoided by keeping the flues and
grates in proper condition.

76. Q. How should cab lamps, signal lamps, oil cans and lanterns be
cared for?

A. They should be kept clean, free from leaks and always filled and
ready for service before leaving terminals.

77. Q. About how many drops in a pint of valve oil when fed through a
lubricator?

A. About 4,500 drops.

78. Q. Assuming that five drops per minute are fed to each of two valves
and one drop per minute to the air pump, how many hours would be
required to feed one pint of valve oil?

A. About eight hours.

79. Q. Assuming that the engine is running twenty-miles per hour, how
many miles per pint would be run?

A. About 160 miles per pint.

80. Q. How many drops per minute should ordinarily be fed?

A. This will vary with the size of the locomotive and the work to be
performed. On small yard engines one drop per minute for each cylinder
is usually sufficient and one drop for the air pump every two or three
minutes. This depends on the condition of the pump and the service being
performed. For large engines in slow freight service four to five drops
per minute, and for large engines in heavy fast passenger service from
five to seven drops per minute should be fed. Air pumps in freight
service where the brake pipe is in moderately good condition can usually
be run with one or two drops per minute when handling long trains of
cars equipped with air brakes.

81. Q. Will any bad results ensue from filling the lubricator full of
cold oil?

A. Yes; when the oil gets hot it will expand and may break the glass or
bulge or burst the lubricator.

82. Q. If a sight feed gets stopped up, how could you clean it out?

A. Close the water valve and the regulating valves to the other feeds.
Open drain cock and draw out a small quantity of water so as to bring
the oil in top part of lubricator below the top end of oil pipe leading
to feed arm, then open wide the regulating valve to feed that is stopped
up and the pressure from the equalizing tube will force the obstruction
out of the feed nozzle and up into the body of the lubricator. Next,
close this regulating valve until the feed glass fills with water, then
open water valve and start feeds.

83. Q. How would you clean out chokes?

A. First, shut off boiler pressure and condenser valve; next, remove
feed valve bonnet, then open main throttle valve, when the steam from
steam chest will blow back through the choke plug, clearing it of any
obstruction.

84. Q. What is superheated steam?

A. It is the saturated steam separated from the water from which it is
generated with more heat added, increasing its temperature from 100
degrees to 250 degrees Fahrenheit above the saturated steam temperature.

85. Q. What is the advantage of superheating or increasing the
temperature of the steam?

A. By increasing the temperature of the steam the volume of a given
weight of steam is increased and all losses due to cylinder condensation
are eliminated, which result in a reduced steam consumption, a saving in
coal and water and increased boiler capacity.

86. Q. How is the increased temperature obtained by the use of the
superheater?

A. By admitting the saturated steam into a partitioned receiver which
has a number of 1-1/2-inch pipes attached to it. These are located in
and extend nearly the full length of the large flues, the steam having
to pass through these 1-1/2-inch pipes on its way back to the receiver,
absorbs the heat from the gases passing through the large tubes, causing
its temperature to rise, or in other words, become superheated.

87. Q. How much is the volume of steam increased by superheating?

A. For each 100 degrees of superheat added to saturated steam, at
temperatures ordinarily used in locomotive practice, the volume of a
given weight is increased roughly from sixteen to seventeen per cent.

88. Q. Why is the superheated steam so much more economical on coal and
water than the saturated steam?

A. Because for a given amount of water evaporated you can increase the
volume of steam 33 per cent. by superheating. It is readily seen that
the coal does not have to be burned if the steam used has 33 per cent.
more volume for filling space, or in other words, only so much steam can
be admitted to the cylinders for every movement of the valve, and what
can not be used must remain in the boiler, so if the engine can not use
all of the steam that the boiler is capable of generating, the saving
must show in coal and water. If you can not use all of the steam you do
not have to burn coal to make it.

89. Q. Which is the better practice, to close the feed valves or water
valve while waiting on sidings, etc.?

A. Close the feed valves; the water valve may leak.

90. Q. How can you tell if equalizer tubes become stopped up or broken?

A. If they were stopped up the equalization would be destroyed, and when
the steam-chest pressure was less than the boiler pressure the feed
would work too fast, the oil would enter the feed glass in a stream
instead of forming into drops. If they were broken, the lubricator could
not be used. The auxiliary oilers would have to be used to lubricate the
cylinders.



=AIR BRAKE QUESTIONS=


1. Q. Explain how an air compressor should be started.

A. A compressor should be started slowly, with the drain cocks open to
allow the water of condensation to escape; and as no provision is made
in the steam end to cushion the pistons at the end of their stroke, it
should be allowed to work slowly until a pressure of thirty or forty
pounds has accumulated in the main reservoir; the piston, having to work
against this pressure, will be cushioned at the end of each stroke.
After the compressor is warm, the drain cocks should be closed and the
throttle opened sufficiently to run the compressor at the proper speed.
The lubricator should then be started and allowed to feed freely until
eight or ten drops have passed, when the feed should be reduced to an
amount sufficient for proper lubrication.

2. Q. What kind of oil should be used to lubricate both the steam and
air cylinders of the compressor?

A. Valve oil.

3. Q. Where does the main reservoir pressure begin and end?

A. Begins at the discharge valves in the compressor and ends at the
engineer's brake valve.

4. Q. Where does the brake pipe pressure begin and end?

A. The brake pipe pressure begins at the feed valve and ends at the
brake pipe side of the triple piston, conductor's valve and at the rear
angle cock.

5. Q. What is meant by excess pressure, and where is this pressure
carried?

A. Excess pressure is carried in the main reservoir and is the pressure
above that in the brake pipe.

6. Q. Why is excess pressure necessary?

A. To insure the prompt release of all brakes and quick recharge of the
brake pipe and auxiliary reservoirs.

7. Q. How is the amount of excess pressure regulated?

A. By the compressor governor.

8. Q. Name the different parts of the air brake as applied to a car.

A. The triple valve, auxiliary reservoir, brake cylinder, brake pipe,
angle cocks, cut-out cock, retaining valve, centrifugal dirt collector
and strainer tee.

9. Q. What is the duty of the triple valve?

A. The triple valve has three duties to perform: Charge the auxiliary
reservoir; apply the brake; and release the brake.

10. Q. What is the purpose of the auxiliary reservoir?

A. It is here that the air is stored that is admitted to the brake
cylinder when the brake is applied; thus, each car carries its own brake
power.

11. Q. What is the purpose of the brake cylinder?

A. It is here where the power of the compressed air is converted into
work by forcing the brake piston out, moving the brake levers, rods and
brake beams, forcing the brake shoes against the wheels, applying the
brake.

12. Q. What is the purpose of the brake pipe and angle cocks?

A. It is through the brake pipe that all brakes in the train are placed
into communication with the brake valve on the locomotive; and through
the brake pipe, air from the main reservoir flows to the triple valves
and auxiliary reservoirs on the different cars. The angle cocks are for
the purpose of opening and closing the ends of the brake pipe.

13. Q. What is the purpose of the cut-out cock?

A. To cut out any brake that is not in operating condition.

14. Q. How is a brake cut out?

A. By closing the cut-out cock in the cross-over pipe and bleeding the
auxiliary reservoir.

15. Q. How would you bleed an auxiliary reservoir?

A. By holding open the release valve on the reservoir until all air has
escaped.

16. Q. How would you bleed off a stuck brake?

A. By holding open the auxiliary release valve until the brake piston
starts to move toward release position.



=OIL BURNING LOCOMOTIVES=


1. Q. What are the fireman's duties on arrival at the enginehouse
previous to going out on an oil burning locomotive?

A. In addition to the duties usually performed on any engine, the
fireman should observe the condition of draft pans and arch, observe the
condition of burner and dampers; try the oil regulating valve; see that
the burner is properly delivering fuel oil to the fire; see that the oil
heaters are in working order; that the fuel oil is heated to proper
temperature; and see that proper supplies of fuel oil, sand and water
have been provided as well as the necessary tools for handling an oil
fire.

2. Q. How warm should the oil be at all times in the tank.

A. Warm enough to flow freely at all times, usually about 112 degrees.
This temperature is about that which the hand can bear on the outside of
the tank.

3. Q. If the oil is too warm, what happens?

A. Many of the good qualities of the oil may be lost by keeping it too
warm, and the burner is more difficult to operate and does not work as
well when the oil is kept at too high a temperature. Should the oil be
too warm, it will give off too much gas which would be liable to cause
an explosion in the oil tank.

4. Q. What tools are necessary for firing purposes on an oil burning
locomotive?

A. The tools necessary for firing an oil burning engine include sand
horn, brick hook, and a small iron bar to be used in cleaning carbon
from the mouth of the burner.

5. Q. What is liable to happen if the heater valve is open too much?

A. If the heater valve is opened too much it would be liable to burst
the heater hose as well as to heat the oil to a too high temperature and
place an unnecessary strain on all the heater connections, causing them
to leak.

6. Q. What should be done on approaching stations where additional
supply of fuel oil is to be taken?

A. Shut off the fire, close safety and main oil valves, remove any lamps
that are so close as to be unsafe when manhole cover is open.

7. Q. What care must be exercised in the use of lamps, torches or
lanterns about oil tanks whether hot or cold?

A. Never permit oil lamps or oil torches to be carried within ten feet
of the tank opening. Only incandescent lamps or pocket flash lights
should be used around oil tank manhole when taking oil.

8. Q. How can oil in the tank be measured without taking a light to the
manhole?

A. By inserting a measuring stick into oil in tank and taking stick to
the light for reading.

9. Q. What precautions must be taken before entering tanks that have
been used for oil to clean or make repairs?

A. Oil tanks, before being entered by workmen, should be thoroughly
steamed and cooled before being entered. For safety they should be
steamed from six to eight hours.

10. Q. How should the fire be lighted in an oil burning locomotive?

A. First see that no one is working under the engine, that there is the
proper amount of water in the boiler and that it will flow through the
gauge cocks, that there is no accumulation of oil in the ash-pan or
fire-box or existing leaks throughout. If there is no steam in the
boiler, the steam connections can be made to the three-way cock at the
smoke-arch that will answer for blower and atomizer. If there are twenty
pounds of steam in the boiler, it can be operated with its own blower.
If oil in the tank is too cold to flow into the burner readily, it must
be heated. Open the front damper and put on the blower strong enough to
create the necessary draft, open the atomizer valve long enough to blow
out any water that might be in the steam pipe to the burner, then close
the valve and throw a piece of burning waste in front of the burner and
open the atomizer valve enough to carry oil to the burning waste and
open the regulating valve slowly until the oil is known to be ignited.
Watch the ignition through the hole in the fire-box door, then regulate
the steam and oil supply to suit. Be sure that no oil is wasting below
the burner or an explosion may result that will prove disastrous.

11. Q. Should the fire go out and it is desired to rekindle it while
bricks are hot, is it safe to depend on the hot bricks to ignite the oil
without the use of lighted waste?

A. No; depending upon the heat from the firebricks to re-light the fire
is dangerous and forbidden.

12. Q. What is termed an atomizer, and what does it perform?

A. The atomizer is a casting containing two long ports with an extension
lip; the upper port is for oil and the lower one for steam. The lip aids
the steam in atomizing and spreading the oil, which, when properly
mingled with the air and ignited, will produce combustion. The atomizer
is located just under the mud-ring and pointed a little upward, so the
stream of oil and spray of steam would strike the opposite wall a few
inches above the bottom if it would pass clear across the fire-box.

13. Q. In starting or closing the throttle of the locomotive, how should
the fireman regulate the fire, in advance or after the action of the
engineer?

A. In starting an oil burning engine the oil should gradually be brought
up as the throttle is opened and the movement and amount of oil should
be kept slightly in advance of the action of the engineer in order to
prevent an inrush of cold air as the engine is working, which would
result in injury to the fire-box and flues. When the throttle is to be
closed, the fire should be reduced very slightly in advance of the
closing of the throttle. This is to prevent the engine from popping off
and black smoke drifting back over the train.

14. Q. Is it necessary that the engineer and fireman on an oil burning
locomotive work in perfect harmony and advise each other of intended
action at every change of conditions?

A. Yes; they should work in harmony with each other on any locomotive.
The fireman should watch every move the engineer makes, and the engineer
should advise the fireman of every intended change of the throttle, so
he can operate his valves accordingly and save fuel and avoid black
smoke.

15. Q. What is the effect of forcing the fire on an oil burning
locomotive?

A. Forcing the fire is very hard on fire-box sheets and flues, and will
cause them to leak. An even temperature should be maintained in the
fire-box of any locomotive.

16. Q. Is a careful regulation of steam and oil valves and dampers
necessary to obtain the most economical results?

A. Yes; the fireman's oil valve should be opened just wide enough to
permit a sufficient amount of oil to be fed to produce a good fire, but
not wide enough to waste oil or produce a volume of black smoke.

17. Q. How can you judge whether the combustion is good or bad, so the
valve may be regulated accordingly?

A. By the color of the fire in the fire-box. When it is a dull red
color, the temperature is below 1,000 degrees and combustion is
incomplete, dense black smoke will issue from the stack. If it is a
bright red, the temperature will be about 1,800 degrees and combustion
very good, and no black smoke will appear from the stack.

18. Q. How should the flues be cleaned from soot when running, and about
how often is this necessary?

A. By placing a small quantity of sand in an elbow shaped funnel or
horn, and by inserting same in an opening provided in fire door while
engine is working hard, allowing the exhaust to draw the sand through
the flues, thus cutting soot and gum from them in its passage and
discharging it from the stack. It is necessary that the flues be cleaned
of soot on leaving terminals or sidings where the engine has been at
rest for any length of time, and also as often as found necessary to aid
the engine in steaming. This depends to a great extent upon the degree
of perfection with which combustion is obtained. Attention should also
be given flues just prior to entering points where engine is to be put
in roundhouse or otherwise detained in order to leave the flues clean,
as this will aid in putting engine under steam with little delay where
the blower alone is to be relied on for draft.

19. Q. Is the injudicious use of the blower particularly injurious on an
oil burning locomotive?

A. Yes; the injudicious use of a blower is injurious to any boiler. The
cold air drawn through the fire-box is hard on the sheets and flues and
will cause them to leak.

20. Q. Is the blower more injurious when a light smoke is emitting from
the stack or when a dense black smoke is emitting?

A. It is most injurious when a light smoke is emitting.

21. Q. In drifting down long grades should the fire be shut off or
burned lightly? Why?

A. The fire should be burned lightly and not permitted to get low enough
to allow the fire-box to lose its temperature, as this will contract the
flues and cause them to leak.

22. Q. How should the fire be handled when switching?

A. The fire must be regulated to meet the requirements of the work the
engine is performing on each move and to protect against any possibility
of the fire being drawn out by the exhaust.

23. Q. Would not some fuel be wasted in this way?

A. Not necessarily. A waste of fuel can be avoided by close attention on
the part of the fireman when switching as well as when running.

24. Q. How should the fire be handled when leaving stations?

A. It should be burning brightly and strong enough to prevent the draft
from putting it out when the throttle is opened. And a little smoke
should show up at the stack, which would indicate that the fire was
being forced just a little ahead of the working of the engine.

25. Q. Which is desirable, to use as much or as little steam jet
atomizer as possible?

A. It is desirable to use as little atomizer as will make engine show
perfect combustion and economy.

26. Q. What is the result of too little steam jet atomizer when standing
at stations or when the engine is working light?

A. The result of too little atomizer when standing at station or when
engine is working lightly, will result in the oil not being carried far
enough into the fire-box or arch and not properly atomized and the fire
is liable to go out. The oil will drop from the mouth of the burner into
the draft pan to the ground where it is very liable to start a fire
under the engine.

27. Q. If too much steam jet atomizer is used with a light fire?

A. It will create a disagreeable gas, which will cause the fire to burn
with a succession of light explosions and kicks, also a waste of steam,
and which would reduce the fire-box temperature.

28. Q. When the fire kicks and smokes, what should be done?

A. The atomizer should be adjusted. If this does not overcome the
trouble, the heater should be put in service, for, possibly, the oil is
too cold to flow freely. Another cause of the fire kicking and smoking
results from water being mixed with the oil. If this is the case, it
should be drained out of the oil tank immediately.

29. Q. How should the dampers be used on an oil burning locomotive?

A. They should be opened just enough to admit sufficient air to produce
perfect combustion, but not enough to cool the fire-box. The dampers
should be closed when the engine is drifting or when at rest and the
fire is cut very low or is out entirely.

30. Q. About how much smoke do you consider an oil burning locomotive
should make under adverse conditions, when the engine is steaming well,
but is being crowded by the engineer?

A. Only a light smoke should show at the stack.

31. Q. What color is most desirable at peep holes in the fire-box?

A. A white color is most desirable.

32. Q. What will produce the bright red color?

A. Leaky steam pipes, side seams, flues and improper combustion will
produce a ruddy color in the fire-box.

33. Q. How does water in the oil affect the fire?

A. Water in the oil will produce popping or kicking with the fire in the
fire-box and at times the fire will die down entirely and then flash up
as the water disappears and the oil reaches the burner. The most
noticeable result of water in the oil is the fact that the fire will get
very low. It will almost go out entirely and then will suddenly flash up
again as the oil appears. Water in the oil produces a very dangerous
condition and should be prevented immediately by draining the water from
the fuel oil tank.

34. Q. Do you consider it advisable to keep the burners clean, and how
often?

A. When equipped with steam blow-out pipes, they should be blown out
before commencing trip so that burners will distribute oil evenly to
each side of fire-box.

35. Q. What position should burner be with reference to level and in
line with center of fire-box?

A. It is very essential that burners be level and throw flames just to
clear floor of arch in order to derive full benefit of heating surface,
as the draft has a great tendency to elevate flames, at opposite end of
the fire-box.

36. Q. Are you aware that in course of time the atomizer port will
become worn too large and will discharge too large a volume of steam to
properly atomize, and the remedy?

A. Yes; the lip or bushing should be closed to proper opening so that
steam will be restricted at the nozzle and escape with a bursting effect
to properly atomize the oil instead of flowing out in quantities against
flash walls before it has time to ignite.

37. Q. What is the real object of having the fire-box lined with bricks,
and will engine steam without them?

A. Not so well as with the brick, the sheets being in contact with water
are too cool to flash the oil readily and hence the use of what is
called a "flash wall" built of fire brick and heated to a very high
temperature aids combustion very materially.

38. Q. Do you consider it your duty to keep close inspection of brick
work as to need of repairs, such as air entering between brick and side
sheets?

A. Yes. To see that plaster is kept between the walls and sheets to keep
cold air from being drawn in.

39. Q. Will engine steam if brick falls in front of burners or in path
of flame and what may be done?

A. No. Remove them with the brick hook or rod by pulling them out
through damper of draft pan.

40. Q. Where engine is equipped with an oil-reheater or oil line, do you
consider it a help to engine's steaming qualities when used?

A. Yes; at all times this heater should be used.

41. Q. Why use second heater? Why not heat it to a high temperature in
oil tank with oil heater?

A. Too much gas generating and boiling the oil continually destroys the
higher qualities besides being hard to control the flow through
regulation valve.

42. Q. Do you consider a vent hole in oil tank advisable, and why?

A. Yes; to allow any accumulation of gas to escape and to admit the air
so that oil will flow freely.

43. Q. Do you inspect your oil pipes and report all leaks? What other
bad effect has a pipe leak aside from waste of oil?

A. Yes. It will cause oil to feed irregularly.

44. Q. Are you aware that keeping the flues clean is the greatest one
thing that you can do in regard to fuel economy, and how often should
they be cleaned?

A. Yes. At least every ten miles.

45. Q. Do you know that the engine should be working hard and at a speed
not less than twenty miles per hour when sanding flues to avoid the sand
falling to floor of the fire-box and accumulating in front of them?

A. Yes.

46. Q. Do you realize that on first closing throttle you should not
adjust fire too low? Explain best method.

A. Yes. I would allow steam pressure to fall back some fifteen pounds
before throttle is closed and on having closed same leave a good fire in
box, allowing it to cool gradually to avoid leaky flues, broken
staybolts, cracked sheets caused by sudden fall of temperature.

47. Q. How is the flow of oil controlled?

A. By the valves in tank and pipe connections.

48. Q. Name these valves, their location and purpose.

A. The safety valve controls the flow of oil from the fuel oil tank
through an opening in bottom sheet of tank to the pipes leading to
burner. This valve is forced to its seat by a heavy spring and is held
off its seat by a key in the upright rod extending above the top of
tank. To this key a rope or chain is attached and also attached to the
cab to cause the pin in rod to be pulled in case of a separation between
engine and tank and allow the valve to be seated by its spring and avoid
a waste of oil. The second or main oil valve is located in oil pipe
under deck leading to burner. It is usually of the plug-cock pattern
connected by bell crank and this connected to some part of the engine by
chain, in which case it also acts as a safety valve in case of
separation between engine and tender. In other cases it is connected by
an operating rod extending above deck of tender where it can be operated
by hand in case of safety valves failure to shut off the flow of oil.
The third or firing valve is usually located between heater box and
burner, and is provided with an upright rod extending into cab where it
is provided with a handle or lever in position to be conveniently
handled by fireman while seated in cab. This valve regulates the flow of
oil desired to reach the fire.

49. Q. When shutting out fire which valve should be closed first? Why?

A. The safety valve. To allow the oil in pipes to be consumed and to see
that this valve is in working order.

50. Q. Should safety valve fail to shut off the flow of oil in such
cases would it be safe to rely on the firing valve to shut off the fire?

A. No. The main valve should then be closed.

51. Q. Should the firing valve be depended upon to shut off the fire at
any time? Why?

A. No. From constant use they are frequently leaking and the trouble is
not detected while in use, and again there is always danger of the
handle being moved by workmen or others about the cab.

52. Q. What is a heater box?

A. It is an apparatus having two passages, one for steam passing from
boiler to heater pipes in tank and another passage for oil from tank
before it is delivered to burner. In this manner the oil before reaching
the burner is heated much higher than the temperature of that contained
in tank.

53. Q. In the event of the heater pipes or connections becoming
defective, how could the oil be heated in tank?

A. By closing the firing valve, closing the valve on heater pipe, and
opening valve on heater box, the steam from heater throttle can be
passed directly through the oil feed pipe to the fuel supply.

54. Q. In the event of an objectionable quantity of water in oil, how
can it be removed?

A. In some instances the tanks are provided with drain pipes for this
purpose, but in the absence of same, the feed hose or pipe between
engine and tank can be disconnected and used as a drain to fuel oil
tank.

55. Q. What effect has leaks between fuel tank and firing valve?

A. A waste of oil only.

56. Q. What effect has leaks between firing valve and burner?

A. In addition to a loss of oil while fire is burning low, and but
little steam atomizer being used, it interferes very materially with
the engine's steaming by admitting air when using considerable steam
atomizer. This causes a very irregular oil feed.

57. Q. What action of the fire would indicate leaks in pipes between
firing valve and burner?

A. The fire-box will give off sounds similar to slight explosions, and
the smoke at stack will indicate irregular fuel feeding.

58. Q. What would you consider the proper adjustment of burner?

A. That which will provide for the delivery of the oil from burner to
flash wall without striking arch, side walls, or floor brick while doing
so.

59. Q. In case it becomes necessary to fire up an oil burning engine
with wood, what parts should be given particular attention?

A. The brick work. To see that same is not damaged or displaced while
placing the wood in fire-box, also to protect by placing brick over that
portion of burner extending into fire-box ahead of mud ring, or by so
arranging the wood in fire-box as to prevent any great amount of heat
from reaching the burner and melting nozzle of same.

60. Q. In case of sudden drop in steam pressure, what might be the
cause?

A. Loose brick perhaps fallen in front of burner and obstructed the flow
of oil. The petticoat pipe may be loose and out of line or the dampers
may have fallen shut.

61. Q. In case brick have fallen in front of burner, how can they be
removed?

A. By a hook provided for that purpose. They can usually be forced out
through the vent openings, but if this cannot be done, they should be
thrown against the blast wall in order to get them as far as possible
out of the course of the fuel feed.

62. Q. In case a petticoat pipe becomes deranged, what can be done?

A. In case it cannot be put back in proper position, it should be
removed altogether. (Trips have been successfully completed in this
manner.)

63. Q. Will a corroded burner mouth prevent the proper delivery of fuel
to fire?

A. Yes.

64. Q. What causes the mouth of burner to corrode?

A. The asphaltum and sand contained in the oil.

65. Q. How can this be removed on the road?

A. By having a hook or rod provided with a point that can be inserted
into mouth of burner.

66. Q. Why should a fuel oil tank not be filled to its holding capacity?

A. Because when heater is applied the oil would expand and overflow.

67. Q. In case of derailment or other accident that might cause the
fireman to desert his position in cab, what should he do?

A. Pull key out of safety valve rod, thereby allowing oil feed from tank
to be shut off.



=MECHANICAL EXAMINATION=

THIRD SERIES


1. Q. What are the duties of an engineman before attaching a locomotive
to the train?

A. He should make a complete inspection of the locomotive, observing all
important nuts and bolts, look for any signs of hot bearings on previous
trip, see that the engine is equipped with necessary tools and supplies,
test both of the injectors and the air brake equipment to be sure they
are in good working order, see that headlight and signal lamps are in
place and ready for service, observe water conditions in boiler, inspect
the interior of the fire-box and see that the locomotive is properly
lubricated.

2. Q. What tools should there be on the locomotive?

A. Such as are necessary to properly operate the locomotive, care for
the machinery, disconnect and block up in case of breakdown and the
necessary firing tools.

3. Q. What examination should be made after any repair work has been
done on valve, brasses, etc.?

A. See that brasses are properly fitted, keys fastened and nuts made
tight. If any repairs have been made on valves or valve gear, would see
that the reverse lever could be moved freely and that all movable parts
had been properly replaced; would also give especial attention with
reference to lubrication of these parts.

4. Q. What attention should be given to boiler attachments, such as
gauge cocks, water glasses, etc.?

A. Would see that the gauge cocks can be opened to try the water and
closed, so steam and water would not come out into cab. Observe the
water glass and note if water is moving up and down in the glass, see
that the steam valve at the top and water valve at bottom of glass could
be opened and closed, and allow water and steam to circulate freely
through the glass.

5. Q. What do you consider necessary to report on locomotive boilers?

A. Should report all defects on boiler and its attachments while engine
is in engineer's charge.

6. Q. Trace the steam from the boiler through the cylinders to the
atmosphere and explain how it transmits power.

A. Steam enters the throttle valve located in the highest part of the
dome in order to get the driest steam, then passes through the standpipe
and dry pipe out of the boiler to the steam pipe tee or nigger-head
located in the front end, then through steam pipes to the steam chest. A
steam valve in each steam chest distributes the steam so that it enters
the cylinders at or just before the beginning of the stroke; pushing the
piston to the end of its stroke; just before the piston reaches the end
of the cylinder, the steam valve opens communication to the exhaust port
through a cavity in its exhaust side, then through the exhaust pipes and
tips up through the draft or petticoat pipe and stack to the atmosphere.
When steam pushes the piston through the cylinder, its power is
transmitted by the main rod to the main crank pin which causes the
wheels to revolve, thus moving the engine and its train.

7. Q. Why is it important that there be no holes through the smoke-box
door or front end and none in smoke-box seams or joints?

A. So as to maintain as good a vacuum as possible in the smoke-box and
prevent small amounts of air coming in through leaks which tend to heat
and warp the smoke-box and its door.

8. Q. How should the locomotive be started to avoid jerks, and what
train and other signals should be looked out for at the time of
starting?

A. Place the reverse lever in full gear, open the throttle valve
gradually so as to start the train one car at a time and easily. Look
for signals ahead to show that the track is clear and switch is in
correct position, then look for signals from the rear end that the train
is all coming.

9. Q. Will an engine equipped with superheat units move as quickly as a
saturated steam locomotive when throttle valve is first opened?

A. No.

10. Q. Why?

A. Because steam must first pass through superheat units before it
enters the steam pipes leading to steam chest.

11. Q. In placing engine on the turntable, at water or stand pipes, or
at other similar places, what must be done?

A. Close throttle valve sooner so that the steam confined in superheat
units, pipes and steam chests, will have passed out to the atmosphere.

12. Q. After a locomotive has been started, how can it be run most
economically?

A. By regulating the supply of steam to the steam chest with the
throttle and the point of cut-off with the reverse lever; so that no
more steam be used than necessary to maintain the proper speed, whenever
possible working the engine at short cut-off so as to use steam
expansively.

13. Q. What is meant by working steam expansively?

A. Hooking the reverse lever up toward the center gives the valve a
shorter travel and closes the live steam port when the piston has made
only a part of its stroke. This cuts off the supply of live steam coming
from the steam chest. The expansion of the steam already in the cylinder
pushes the piston to the end of its stroke without the use of a full
cylinder of live steam.

14. Q. How rapidly should water be supplied to the boiler?

A. No faster than it is evaporated into steam, unless just before a hard
pull; or when shutting off with a heavy bright fire in the fire-box to
prevent waste of steam at the pops.

15. Q. What is the difference between priming and foaming of a
locomotive boiler?

A. Priming is caused by carrying the water too high in the boiler so
that when the throttle valve is opened some of it passes over with the
steam in the form of a spray. Foaming is caused by the water becoming
dirty from animal or alkaline matter, so that heat makes it foam like
soap suds. Muddy water or certain vegetable matters will also make a
boiler foam.

16. Q. What should you do in a case of foaming? What in a case of
priming?

A. In a case of foaming, if possible, allow the boiler to cool off a
little, increase the supply of feed water to prevent water getting too
low, and whenever possible blow some of the dirty water out of the
boiler, replacing it with clean water. In case of priming, shut off the
supply of feed water until the water level drops to the proper height in
the boiler.

17. Q. What danger is there when the water foams badly? When it primes
badly?

A. There is danger of knocking out cylinder heads, cutting the valves,
stalling on some grade or getting on some train's time because the
engine cannot be worked to its proper power. When shutting off steam,
the water is liable to drop below the crown sheet and thus risk burning
the fire-box. When water primes badly, it is liable to break cylinder
packing rings, knock out cylinder heads, break bolts in the steam chest
and cut the valves. In such a case additional oil should be fed to the
steam chest until the valves are properly lubricated.

18. Q. Suppose that with the water glass in good working order,
immediately after closing the throttle the water disappeared from the
water glass, what should be done?

A. Would open the throttle and endeavor to raise water until both
injectors would put enough water into the boiler to make it entirely
safe to close the throttle. If unable to raise the water level to the
lower gauge cock would smother the fire or put it out entirely, if
necessary, keeping both injectors working.

19. Q. What work about a locomotive should be done by the engineman?

A. Inspection of the engine both before and after the trip. The engineer
should do any necessary work on the engine after starting out on the
trip to avoid breakdowns and insure getting over the road promptly. This
means tightening up any important bolts that work loose on the trip and
keeping parts from working out of position, adjusting wedges and rod
keys.

20. Q. How should the work of setting up the wedges be done?

A. Place the engine on the upper quarter on the side with the loose
wedge. Do not set the brake if brake shoe will push the driving box
against the defective wedge, but block engine truck wheels so the engine
cannot move, push the boxes against the shoe or dead wedge with a little
steam, set the wedge up until it is a snug fit, then pull it down about
one-sixteenth of an inch and fasten. Provision should be made for
expansion of the box when it gets warm.

21. Q. How should rod brasses be keyed?

A. If properly fitted they should be keyed brass to brass; if not so
fitted, they should be keyed on the large part of the pin so they will
be free enough to run without heating and snug enough to run without
pounding. Do not key them so tight at either end as to prevent the
lateral motion of the brass on the pins.

22. Q. How should an engine be placed for the purpose of keying the rod
brasses?

A. For the main rod, place the engine on the quarter or the top forward
eighth, whichever place gives the largest diameter of the pin to key the
brass against. After keying up, test by moving the wheel to another
position and see if brasses are free on the pin. For the side or
parallel rods, always place the engine on the center for the side that
is to be keyed.

23. Q. How should the side rods on a mogul or consolidation locomotive
be keyed?

A. Place the engine on the center on that side, key up the brass on the
main pin first, work each way toward the ends of the rods, being careful
to keep them the proper length so they do not bind when passing either
center. Be sure that wedges are properly set up before keying the side
rods.

24. Q. What is the necessity for keeping the brasses keyed up properly?

A. If too tight, they will surely run hot; if too loose, they will pound
and injure the brasses as well as endanger the safety of the straps and
rod bolts. Very loose brasses can pound enough to get hot.

25. Q. What is meant by an engine out of tram? Out of quarter?

A. When corresponding wheels on opposite sides of the engine on
different axes are not spaced equally apart; where the axle of any wheel
is not at a right angle to the center line from front to rear of engine,
so they do not run square on the rails, or where the space between the
axle centers on opposite sides is not equal. This is sometimes indicated
by unequal flange wear and should be reported at once. Wheels are out of
quarter when the crank pin in one wheel is not exactly 90 degrees or one
quarter of a turn from the pin in the wheels on the other end of the
same axle. This is usually caused by slipping the engine with sand on
one rail only and the condition of engine should be reported at once.

26. Q. Describe a piston valve.

A. A piston valve is a cylindrical spool-shaped valve constructed with
packing rings much the same as the steam piston that moves through the
cylinder, except that a piston valve is double or composed of two
pistons connected by center rod or spool working in a bushing of equal
diameter. Steam and exhaust ports are cut through this bushing; steam
ports to the cylinder and exhaust port to the exhaust pipe. There is
also a steam port for live steam from the boiler. As the pressure on
this valve is equal in both directions it is practically balanced.

27. Q. What is a balanced slide valve? How is it balanced, and why? For
what purpose is the hole drilled through the top of the valve?

A. One in which the steam pressure on the top and bottom of the valve is
nearly equalized. This is done by protecting a portion of the top of the
valve from the steam pressure. It is usually balanced by strips held
against the pressure or balance plate by one or more springs. This is
done to prevent live steam from getting on top of valve and thus relieve
the valve from the top pressure which would cause excessive friction
between the bottom of the valve and its seat. The hole through the top
is to allow any steam which might leak by the strips to pass into the
exhaust, so pressure could not accumulate on the top of the valve, also
to equalize the exhaust pressure between the top of the valve and
exhaust cavity as well as to assist in lubricating the balance plate.

28. Q. What is meant by inside and outside admission valves?

A. With an inside admission valve (usually a piston valve), the live
steam comes between the piston valve heads, the outside end of the heads
being connected with and exposed to exhaust pressure, it admits steam
past the inside edges of the valves. An outside admission valve has the
space between the ends connected to the exhaust and a space at the ends
connected with the live steam. It admits steam past its outside edges. A
piston valve can be either inside or outside admission, while a slide
valve is always outside admission.

29. Q. What is the relative motion of the main piston and the steam
valves for inside admission, and, on the other hand, for outside
admission?

A. If the piston is in the front end of the cylinder, an inside
admission valve must move forward in order to connect the inside of the
valve with the front live steam port to admit steam against the piston.
The outside end of the valve opens the exhaust port for the back end of
the cylinder. In the same position of the piston an outside admission
valve must move backwards to open the steam port or in the same
direction as the steam piston when commencing its stroke.

30. Q. What is an Allen ported valve, and what is its object?

A. An Allen ported valve is an outside admission slide valve having an
extra port from one end of the valve to the other, above the exhaust
cavity and through the body of the valve. This extra port is calculated
to admit steam through the valve at the same time that steam passes by
the end of the valve into the same steam port, thus doubling the area of
opening for live steam when the port is first opened.

31. Q. What is the difference in the valve motion for outside admission
valves and for inside admission valves?

A. An outside admission valve must be moved in the opposite direction to
an inside admission valve in relation to the movement of the steam
piston when beginning its stroke; therefore either the position of the
eccentric or the position of the rocker arms in relation to the rocker
shaft must be opposite for a change in these valves.

32. Q. What is a direct motion valve gear? What is an indirect motion
valve gear?

A. A direct motion valve gear is one in which the valve moves in the
same direction as the eccentric rod, that is doing the work, in many
cases no rocker arm is used. In case a rocker arm is used, both arms
point in the same direction like the letter U. An indirect motion valve
gear is one in which the valve moves in an opposite direction to the
eccentric rod doing the work. A rocker is used in which the arms point
in opposite directions from the shaft connecting them. Owing to the
design and construction of the Walschaert valve gear, it is a direct
motion gear when the engine is running in one direction with the link
block in the bottom of the link, an indirect motion when the engine is
running in an opposite direction with the link block in the top of the
link; usually direct motion when running forward.

33. Q. How can you detect the difference between a blow in valve or
piston packing?

A. A blow from the valve is more constant and has a somewhat different
sound, while a blow from cylinder or piston packing will blow stronger
at the beginning of the stroke and gradually decrease as the stroke is
completed.

34. Q. How would you place engine to locate broken admission steam ring
in piston valve?

A. Would place engine on quarter, reverse lever in center so as to cover
ports, then open throttle; and the steam will blow out of cylinder cock
at the end of cylinder where broken valve ring is located.

35. Q. How would you locate broken exhaust ring in piston valve?

A. Watch the cross-head when engine is working steam. As there will be
three normal and one light exhausts, you can determine on which side of
the engine the light exhaust takes place.

36. Q. What is meant by lead? What by line and line?

A. Lead is the amount of port opening for live steam to cylinder ahead
or back of piston when the piston is on the dead center. If the steam
edge of the valve is in line with the edge of the steam port when the
piston is on the center, it is said to be line and line.

37. Q. What is meant by steam lap?

A. The distance that the valve overlaps the live steam edges of the
steam ports when it is in the center of its travel over the seat. This
distance is measured at one end only, although the valve laps equally at
both ends.

38. Q. What is meant by exhaust lap? What by exhaust clearance?

A. Exhaust lap is the distance that the exhaust edge of the valve
overlaps the exhaust edge of the steam port when the valve is in
central position. Exhaust clearance is the opening between the exhaust
edge of the valve and the exhaust edge of the steam port with valve in
central position. If the valve has neither exhaust lap or clearance it
is said to be line and line.

39. Q. What is meant by release? What by compression?

A. Release is the point in the travel of the piston when the port is
opened. Compression is the distance the piston travels after exhaust
port closes before the live steam port opens. During this travel of the
piston the exhaust port is closed so the moving piston compresses the
steam left in the cylinder.

40. Q. With an indirect valve motion and outside admission valve, what
would be the position of the eccentric relative to the crank pin on that
side? What with a direct valve gear? What difference between outside
admission valve and inside admission valve as to this position?

A. With an indirect valve motion and an outside admission valve, the
go-ahead eccentric follows the crank pin with engine running ahead.
Without any lap or lead it would be a quarter of a turn or 90 degrees
behind the pin, but as all valves have lap and lead, the eccentric is
advanced or placed toward the pin enough to move the valve the amount of
the lap and lead. With a direct valve gear and an outside admission
valve, the eccentric will be a quarter of a turn or 90 degrees ahead of
the crank pin and advanced enough to move the valve the amount of the
lap and lead. With an inside admission valve and an indirect valve
motion, the eccentric will come the same as for an outside admission
valve and direct motion, or more than a quarter of a turn ahead of the
pin. With an inside admission valve and direct motion, as piston valves
are usually put up, the eccentric will follow the pin less than a
quarter of a turn.

41. Q. What effect would be produced upon the lap and lead by changing
the length of the eccentric rod?

A. Lap depends on the construction of the valve. A change of the
eccentric rod would not effect it, but would widen the port opening at
one end of the travel and reduce it at the other. It should be equal at
both ends. Lead is controlled by the position of the eccentric on the
axle and it must be equal at both ends. Changing the length of the
eccentric rod from the proper one does not really affect the lead,
because no proper measurement can be made until lead is equal at both
ends. Therefore improper length of eccentric rods varies the port
opening at the beginning of the stroke of the piston at both ends.

42. Q. Why are eccentric rods made adjustable?

A. In order to change their length to make adjustment of the valve gear
not as easily made in other ways.

43. Q. Why is it necessary to keep the cylinders free from water?

A. In order to avoid damaging valves and cylinders, to insure perfect
lubrication and obtain the most efficient service from the locomotive.

44. Q. Where is the piston rod packing located? Where cylinder packing?

A. Piston rod packing is usually soft metallic rings located inside of a
gland at the back end of cylinder and around the rod. Cylinder packing
rings are usually cast iron, placed around the piston head and bearing
against the walls of the cylinder.

45. Q. How are metallic packing rings on piston rods and valve stems
held in place? What provisions are made for the uneven movements of the
rod?

A. The packing rings fit into a vibrating cup or cone located inside the
gland, being held therein by means of a spring as well as by the steam
pressure. Provision is made for uneven movement of the rod by making the
inside of the gland larger than the vibrating cup and using a ball-joint
ring between the vibrating cup and gland.

46. Q. While running under steam and there is a failure of part of the
locomotive which does not seem to prevent running at full speed, how
would you proceed?

A. Keep the locomotive running if in your judgment it is safe. Try to
ascertain what the injury is and be prepared at the next stop to do such
work as the case demands, being careful to make the stop at such a place
that the work can be done without interfering with the movements of main
line trains.

47. Q. If one side of a locomotive is disabled, what would you do in a
general way to make it possible to use steam on the other side?

A. Disconnect enough parts to allow for the turning of the wheels and
for reversing of the opposite side without moving the valve on the
disabled side.

48. Q. In case a locomotive in your care became disabled on the road,
what would you do?

A. First see that the train is protected. Next examine the locomotive
and see what is necessary to do to move it and if possible the train. If
unable to make repairs at once to bring the engine and train forward,
would advise exact condition of engine and ask for help. In the meantime
endeavor to move the train so as to give other trains the use of the
main line.

49. Q. Suppose a wash-out plug blew out or a blow-off cock broke off or
would not close, what should be done?

A. Kill the fire, get the train on a side track, if possible, and if
unable to make repairs get the engine in condition to be towed in. In
all cases with a disabled engine allow the train to drift to a siding,
when possible, and stop between the switches so as to allow other trains
to pass through siding.

50. Q. Can a locomotive boiler without steam pressure be filled by being
towed by another engine? If towed, how filled?

A. Yes. Close all openings where air could enter the boiler. All relief
valves, cylinder cocks, gauge cocks, the whistle valve and air pump
steam valve should be closed. Place the reverse lever in full gear in
the direction the engine is to be towed with water supply valve and
injector throttle open. Use engine oil through auxiliary oil cups to oil
valves and pistons. The movement of the pistons in the cylinders will
pump the air out of the boiler and atmospheric pressure on water in the
tank will force water into boiler when the engine is towed.

51. Q. What should be done if grates should be burned out or broken
while on the road?

A. Pull the fire off the broken or burned grates, cover that section
with any pieces of iron at hand (fish-plates or angle-bars are very
good), then level up the fire, clean ash-pan and proceed with full
train.

52. Q. What precaution should be taken to prevent locomotive throwing
fire?

A. The netting and smoke-arch should be kept in good condition; cinder
slide and hand hole plates securely fastened, ash-pan clean and slide
dampers for dumping ashes closed. Care should be exercised in working
the engine, especially in the vicinity of stations or places where fire
is liable to catch. Avoid working the engine hard so as to prevent
throwing cinders.

53. Q. What shall be done with a badly leaking or bursted flue?

A. Plug it if possible with an iron or wooden plug. If in the fire-box
end, a piece of scantling or post can be sharpened and driven into the
flue from the fire-box door; it will then burn off up to where the water
from the bursted flue keeps it wet. If a bottom flue, would cover it
with ashes or green coal so that the leakage would not put out the
balance of the fire. If able to maintain steam pressure, would then
proceed with a full train.

54. Q. What should be done in case the throttle valve stem became
disconnected while the valve is closed? If it became disconnected
leaving valve open?

A. Would notify the train crew and Dispatcher and arrange to be towed
in. With lubricator working, unless in very cold weather so there is
danger of the water freezing in the cylinders or steam chest passages,
would not disconnect. By taking out lubricator chokes and steam chest
valves from the oil pipe, a larger supply of steam could be got into
the cylinders. If in to clear of other trains and practicable, would
take up the dome cap and connect the throttle again. If disconnected and
valve stuck open, would notify the train crew and Dispatcher, reduce
steam pressure until the engine could be handled with reverse lever and
brake, and proceed with such a train as the engine can handle.

55. Q. In case a valve yoke or stem became broken inside of steam chest,
how can the breakage be located?

A. In this case the disabled valve is always pushed to the front end of
the steam chest so that with a slide valve or outside admission piston
valve the back port is open to live steam. When given steam, the engine
will stop on the eighth, and when reversed will move over to the other
eighth, being stopped there by the live steam in the back end of the
cylinder having the disabled valve. Steam will blow from the back
cylinder cock on the disabled side and cannot be changed by reversing
the engine. If the valve is pushed far enough ahead to open the exhaust
port, steam will blow through the exhaust so the engine cannot be moved.
With an inside admission valve the forward steam port will be opened and
steam will come out of the forward cylinder cock on the disabled side.

56. Q. After locating a breakage of this kind, how would you proceed to
put the engine in safe running order?

A. Would move the valve to central position so as to cover both steam
ports, if possible. This may be done by taking out the relief valve if
on front side of the steam chest and pushing valve back, or taking up
the cover for a slide valve; or taking off front head for a piston
valve. Disconnect the valve rod from rocker arm and block valve stem so
it cannot blow out of the gland or let valve work back. Loosen cylinder
head in order to provide for lubricating cylinder so as to leave the
main rod up on the disabled side and proceed on one side. If unable to
cover the open steam port it would be necessary to disconnect the main
rod on the disabled side, blocking the piston at the proper end of the
guides so live steam coming into the cylinder would not move it.

57. Q. If a slide valve is broken, what can be done to run the engine on
one side?

A. Remove the steam chest cover, place a thin board between the valve
and the steam passages in the seat, replace steam chest cover,
disconnect valve rod, and if able to lubricate the cylinders leave up
the main rod and proceed on one side.

58. Q. If one of the bolts connecting the two parts of a built-up link
on Stephenson gear breaks or is lost, how would you proceed?

A. If temporary bolt cannot be supplied, take down the forward part of
the link, disconnect and remove link block, fasten valve to cover ports,
and proceed. If moving link will clear rocker arm or other parts of the
machinery after link block is taken out, it will not be necessary to
disconnect eccentrics.

59. Q. What should be done in case of link saddle pin breaking?

A. Remove the broken parts and block the disabled link in such a
position that the entire train could be started, using a very short
block above the link block in the link slot and a longer one below it.

60. Q. With one link blocked up, what should be guarded against?

A. Reversing the engine or moving the tumbling shaft arm down so the
link on the disabled side can strike it.

61. Q. How can it be known if an eccentric has slipped on the axle?

A. By the uneven exhaust of the engine and a thorough inspection to
determine the cause.

62. Q. Having determined which eccentric has slipped, how should it be
reset?

A. Place the engine on the center on disabled side and if a back-up
eccentric has slipped, would place the reverse lever in full forward
gear and mark the valve stem flush with the gland; then place the
reverse lever in full back gear and move the slipped eccentric until the
mark on the stem returns to its original position, taking notice that
the throw of the eccentric is on the other side of the axle from the
go-ahead eccentric used as a marker, and tighten up set-screws. To set a
go-ahead eccentric, use the back-up one on that side for the marker. If
the eccentric had been keyed on, would move the cam until the key-way in
the axle came in line with the slot in the cam. Knowing the position of
the eccentric in relation to the crank pin, an inspection would show
where it belongs. The eccentrics are usually opposite the third spoke in
the driving wheel from the pin, sometimes ahead of the pin, in other
cases back of the pin, depending on whether it is an inside or outside
admission valve, a go-ahead or back-up eccentric.

63. Q. What should be done in case of a broken eccentric strap or rod?

A. For a go-ahead strap or rod take down all broken parts, disconnect
valve rod, cover ports, and come in on one side. It is safer to take
down also the back-up strap and rod on that side. If the back-up strap
and rod is broken, it is possible to secure the bottom end of the link
so it will not turn over, work the engine full stroke ahead, proceeding
with full train until the main line is clear.

64. Q. How should the engine be disconnected if the lower rocker arm
became broken? If link block pin?

A. Would remove broken parts; if moving link would strike anything
connected with the rocker box or broken arm it would be necessary to
take down both eccentric straps and rods. Block valve central over ports
and come ahead on one side. If a link block pin was broken, it might be
possible to put a bolt in there to do the work, otherwise block the
valve on the center of its seat and if the link will not clear the lower
end of the rocker arm take down the eccentric straps and rod. In any
case where necessary to take off the eccentric rod always take off the
strap also.

65. Q. For what breakdown is it necessary to take down the main rod? The
side rod?

A. A broken main crank pin, broken main rod or strap, broken piston rod
when near the middle of the rod, broken cross-head or guide, broken
valve or seat when steam cannot be kept out of the cylinder. Side rods
must come down for broken side rod, broken main pin, or broken side rod
pin affecting that rod.

66. Q. If it is not necessary to take down the main rod of disabled side
of the engine, how would you arrange to lubricate the cylinders?

A. If cylinder and piston are in good shape and it is possible to block
the valve to admit a small quantity of steam into the back end of the
cylinder, oil from the lubricator will go through this opening and oil
the piston rod and cylinder packing. If not possible to block the valve
properly, cover the ports and oil the cylinder through the indicator
plug openings or relief plug holes. If not possible to do this, slack
off the bolts on the front cylinder head, wedge the head open so oil can
be introduced. In some cases it may be necessary to take the head off;
that however, allows dust and grit to enter the cylinder.

67. Q. What is the by-pass valve, and what is its duty?

A. By-pass valves are connected to the steam port leading to the
cylinder. Its duty is to open when the engine is drifting with steam
shut off, and close when working steam, to allow air to pass back and
forth from opposite sides of the moving piston.

68. Q. What is a vacuum relief valve? What a cylinder relief valve?

A. A vacuum relief valve is usually located on the steam chest or the
live steam passage to the chest and opens when steam is shut off and
engine drifting, allowing atmospheric pressure to pass into the steam
chest, closing when working steam. A cylinder relief valve is a pop
valve screwed into the cylinder head and set at high enough pressure so
it does not open in ordinary service, but will open to allow water to
pass out when the exhaust port is closed by valves; or on compound
engines when the pressure in the low-pressure cylinder gets too high.

69. Q. What would be considered a bad engine or tender truck wheel?

A. One loose on axle; having bad flat spots; very sharp flanges; bad
sand spots; cracks shelled out; or other defect that would make the
wheel unsafe.

70. Q. What should be done if a tender truck wheel or axle should break?

A. Would place a piece of timber or rail across the tender, jack up the
corner of the truck that is disabled chain it to the timber and fasten
the timber at the other end to hold it so it would carry the disabled
truck. If it is possible to slide the wheel or truck, place a tie across
the rail and keep the wheel from turning, then slide it to a siding.

71. Q. What should be done if an engine truck wheel or axle should
break?

A. Would block between the engine frame and truck frame over the good
wheel on disabled side, swing the disabled corner of the truck to the
engine frame with a chain. Look out when crossing frogs that disabled
truck does not leave the track. With a broken flange, would block the
wheel to prevent its turning and skid it to a siding.

72. Q. What should be done for a broken tender truck spring?

A. Jack the tender up to where it belongs and put a block in place of
the broken spring.

73. Q. What should be done with a broken engine truck spring or
equalizer?

A. For a broken spring, raise the front end of the engine and place
blocks across the equalizers under the truck spring near the spring
band. For a broken equalizer, block on top of engine truck boxes and
under truck frame.

74. Q. What should be done if a driving spring hanger or equalizer
should break?

A. Would block between the driving box affected and under the frame over
it, using hardwood block or piece of iron. Would also block the
equalizer up to its proper position between the disabled end and the
frame, or over the other end, as the type of spring rigging requires, to
hold the equalizer level. For a broken equalizer, would block on top of
all boxes affected, would raise the engine by running the proper driving
wheels upon an incline or wedge to lift the engine while other boxes
were blocked; a re-railing frog comes handy for this work.

75. Q. How can an engine be moved if the reverse lever or reach rod were
caught at short cut-off by a broken spring or hanger?

A. By removing the pin at the forward end of reach rod, to free the
tumbling shaft and allow it to be moved either forward or back to move
the engine. A block should be placed over the link block to avoid
damaging it when uncoupled, as well as to hold link in proper position
to move the engine. This would allow the engine to be moved and clear
the main line.

76. Q. How can the blowing of steam past cylinder packing, a valve or
valve strip be distinguished or located?

A. Test for a leaky slide valve, place the engine on the quarter on the
suspected side with the reverse lever in center notch; the valve should
be in the middle of its travel and cover both ports. If steam blows
through the open cylinder cocks on that side, the valve or seat are
defective. A leaky balanced valve strip will allow steam to blow through
the hole on top of the valve into the exhaust port in the seat and very
little steam will come out of the cylinder cock; in some cases with the
valve barely opening a steam port to the exhaust, air will draw in at
the cylinder cock. If there is a drip cock in the exhaust pipe under the
saddle, the steam will blow out there. After testing for leaky valve,
place the engine on about the forward bottom or top back eighth, block
the wheels or set the brakes solid, put reverse lever in corner, open
cylinder cocks and give the engine steam. If steam comes out of both
cylinder cocks, and testing valve shows it is tight, then the packing is
blowing. Cylinder packing should be tested with steam first on one side
of the piston and then on the other.

77. Q. If engine should blow badly and be unable to start the train when
on the right dead center, on which side would be the blow generally?

A. On the left side. If the side standing on the quarter cannot start
the train, the trouble is usually there.

78. Q. If throttle were closed and steam came out of cylinder cocks,
what might be the cause?

A. To test for this, first shut off steam connection to the lubricator;
steam leaking into the cylinders can come from a leaky throttle or leaky
dry pipe.

79. Q. Is it possible to distinguish between a leaky throttle and a
leaky dry pipe?

A. Yes; a leaky throttle usually leaks steam at all times. A leaky dry
pipe will leak both steam and water. It will show a stream of water at
the cylinder cocks when the water level in the boiler is raised above
the leak in the dry pipe.

80. Q. What effect have leaky steam pipes in the smoke-arch, and how
should they be tested?

A. Leaky steam pipes waste steam and very seriously affect the draft in
the front end. A bad leak in the back part of the joint at the bottom
will blow into the tubes and make the engine smoke at the door with
throttle wide open while standing still. To test them, open the front
door and cover the joint with fine cinders. When the engine is given
steam, the cinders will blow away from the leak; to properly test them
in the shop, water under heavy pressure should be used.

81. Q. How should the test for a leaky exhaust pipe joint, or a leaky
nozzle joint be made?

A. About the only test that can be made on the road is to open the front
end and reverse the engine with throttle partly opened, watching the
suspected joint at the same time. For the bottom one with cinders around
the joint, for the top one it can sometimes be detected by holding a
torch near the joint.

82. Q. What should be done if a steam chest cracks?

A. Would loosen up the steam chest cover to free the sides, and wedge
between the studs and walls of chest, crowding the broken parts
together. A brake shoe key does this nicely. Would then tighten down on
steam chest cover and proceed.

83. Q. What should be done if a steam chest breaks?

A. Would take off steam chest cover, place strips of boards over the
steam inlets and block on top of them so that the steam chest cover
would hold them in place and prevent live steam coming out of inlet.
Would then make the necessary disconnection and proceed on one side.

84. Q. If a link lifter or arm were broken, what should be done?

A. Take off the disabled parts, block between the top of the link and
link block, having the disabled link blocked down very nearly in full
strokes. For safety, both the top and bottom of the disabled link should
have blocks in its slot; the good link would be held in place by the
reverse lever and should under no consideration be dropped down any
farther than the disabled link was.

85. Q. If the reverse lever or reach rod should break, what should be
done?

A. If either breaks, place an iron bar or suitable piece of material
across the top of both frames, securely fastening it in position, then
fasten the arm of the tumbling shaft to the bar. This will require the
engine to be worked at about half cut-off; handle such part of the train
as the road conditions would permit.

86. Q. What should be done if the piston, piston rod, cross-head, main
rod or crank pin are broken or bent?

A. If a piston should break, would remove broken parts, disconnect valve
stem, clamp valve in central position, and if moving piston would not
damage cylinder, leave main rod up and proceed. If a piston rod,
cross-head, main rod or crank pin are broken or bent, would take down
the main rod, block the valve and cross-head; if piston rod is broken
off at the cross-head, leave main rod up.

87. Q. What should be done when there is a loose or lost cylinder key?

A. If the cylinder key is loose, it should be tightened up; if lost,
something should be substituted. In case nothing solid can be found to
take the place of the key, the engine should be run in light to avoid
further damage.

88. Q. What should be done if a safety valve spring or stud breaks?

A. The steam pressure should be reduced. With broken spring, screw the
parts down solid or clamp the stem down. This can be done by laying a
piece of scantling across the top of the valve, fastening each end to
the hand rail on opposite sides of the engine in case of broken stud.
Would then raise steam pressure and proceed. Care should be taken to see
that the other safety valves relieve the steam pressure properly.

89. Q. How can an engine be brought in with a broken front end or stack?

A. By boarding up the front end to make it as near air tight as possible
and using a barrel or a petticoat pipe in place of the stack, wiring it
fast to the smoke-arch. Where a portion of the stack is inside the
smoke-box the engine might steam without the barrel or petticoat pipe.

90. Q. What should be done if the frame is broken between the main
driver and cylinder?

A. Either give up the train and come in light, or disconnect the engine
on that side and come in with reduced tonnage, depending on how badly
the engine pounds when working steam.

91. Q. If the frame is broken back of the main driver?

A. Do not disconnect and do not try to pull a heavy train; it is safer
to come in with light tonnage.

92. Q. In case of broken side rods, what should be done?

A. Take down the broken rod and corresponding rod on the other side of
the engine.

93. Q. What can be done if the intermediate side rods were broken on a
consolidation engine having the eccentric on the axle ahead of the main
wheel?

A. In this case the engine must be towed in. It is possible when the
main pin is broken, so that all rods on one side are taken off, to leave
the rods up on the other side and move the engine with her own steam,
but very few roads will allow this, because engineers will be inclined
to leave the main rod up on the disabled side to prevent engine catching
on the center. If main rod is left up on the disabled side, the wheels
will surely slip and wreck the rods on the other side.

94. Q. Should one of the forward tire, main tire, intermediate tire,
back tire, or a trailer tire break, what must be done to bring the
engine up?

A. Would run the wheel of the broken tire on a block in order to raise
the wheel clear of the rail and the box up in the driving box jaws.
Remove the oil cellar and place a block between the driving journal and
pedestal brace to carry the disabled wheel center clear of the rail.
Would also block up on top of the box of the wheel ahead or back as the
case might be, in order to take the weight from the disabled wheel. It
might not be necessary to take off any of the rods, but would run the
engine light to the shop, giving special attention to lubrication of the
disabled wheel and using extra precaution in entering side tracks and
passing over frogs and switches. With the tire of a back driver or
trailer wheel broken, it is usually necessary to swing the rear end of
the engine from the tender to keep the rear end on the track. With an
inside radial journal, box on the trailer axle; for a broken trailer
tire, both trailer wheels must be blocked and swung clear of the rail.

95. Q. What is a good method of raising a wheel when jacks are not
available?

A. By raising the wheel on a hardwood block or iron wedge; a re-railing
frog comes very handy for this purpose.

96. Q. How can it be known when the wedges are set up too tight and the
driving box sticks, and in what manner can they be pulled down?

A. If wedges are set up too tight, it causes the boxes to stick and the
engine to ride rough. Inspection of the engine when moving will locate
the disabled box; usually this gets hot at once and the wedges should be
immediately pulled down. Loosen the jam nuts on the wedge bolts and back
them down; if the wedge is stuck very tight it may be necessary to run
one or more of the wheels over a block; or to loosen the pedestal, brace
bolt and allow the jaws to spread to release the box.

97. Q. What are some of the various causes for pounds?

A. Wedges not properly adjusted, loose or worn driving box brasses, rod
brasses not keyed or in need of reducing, loose side rod bushings or
side rod connections, worn cross-heads, wrist pins, broken frame, loose
cylinder key, loose piston on rod, or rod loose in cross-head, loose
follower bolts or obstruction in the cylinder.

98. Q. How may a pound in driving boxes, wedges or rod brasses be
located, and after locating what should be done?

A. Place the engine at half stroke on side to be tested. Do not set
brake when testing for loose wedges or defective boxes; set brake when
testing for other pounds. Reverse engine from forward to back gear under
steam, noting the movement of the axle in the boxes, the driving boxes
between the wedges, rod brasses on the pins and movement of cross-head
between the guides. If possible would adjust wedges or rod brasses at
once and report repairs needed at the terminal.

99. Q. How locate loose follower bolts?

A. Shut off steam and allow engine to drift; there will be a pound in
the cylinder when the loose follower bolt strikes a forward
cylinder-head as the engine passes the forward center on that side; give
engine steam while still moving and if the pound stops it is likely to
be a loose or broken follower bolt. When working steam, the compression
or pre-admission takes up the lost motion in the rod and connections, so
the loose bolt does not strike the head; when shut off the piston
travels the extra amount of this lost motion and the bolt strikes the
head.

100. Q. When should cross-heads or guides be reported to be lined?

A. When there is excessive lost motion between the cross-head and the
top and bottom guides, or between the cross-head and the guide at the
sides, or when the piston rod is not central between the guides.

101. Q. When should driving box wedges be reported to be lined?

A. When they have been set up as far as possible and the boxes are still
loose between the wedge and shoe. At this time would also report any
excessive flange wear on any one particular tire.

102. Q. When should rod brasses be reported to be reduced? When to be
lined?

A. Rod brasses should be reported reduced when they are larger than the
pins and are pounding and cannot be keyed up properly. They should be
reported to be lined when the key has been drawn or driven to its full
length and the brasses do not close together or are too loose in the
strap lengthwise of the rod.

103. Q. When should lost motion between engine and tender be taken up?

A. When the lost motion becomes so great as to endanger the breaking of
connections.

104. Q. How do you proceed to pack a driving box equipped with a grease
cellar?

A. Remove the filling plate on the inside of the cellar. Pull down the
indicators and follower plates, insert the grease between the follower
plate and perforated plate; when full, replace the filling plate on the
inside of the cellar and allow the spring and follower plate to force
the grease through the perforated plate to the journal.

105. Q. Please explain the principle on which an injector works.

A. With a lifting injector the steam valve is opened a small amount to
furnish steam for the priming or starting jet. This forces the air in
the body of the injector and top end of suction pipe out through the
overflow valve, producing a partial vacuum in the body of the injector.
Atmospheric pressure in the tank then forces the water into the injector
body. When it begins to come out through the overflow, a further
movement of the steam valve opens the forcing valve wide, so a full
supply of steam strikes the water at a high velocity and at the same
time condensing. This action of the steam gives the water sufficient
velocity to overcome the boiler pressure and pass into the boiler.

106. Q. Explain the passage of steam from the boiler to the steam heat
pipe.

A. Steam is admitted to the steam heat pipe, in which there is placed a
reducing valve through which it passes at reduced pressure, into the
steam heat pipe under the entire length of the train. The reducing valve
is located in the cab close to the steam heat throttle.

107. Q. If the steam heat gauge shows proper pressure, but the steam
heat pipe pressure appears to be low, what should be done?

A. If the steam heat gauge is showing the correct pressure, there is an
obstruction in the pipe somewhere, most likely in the steam heat hose,
and this should be looked for and remedied; if the gauge is correct,
then it is the reducing valve that is at fault and this should be
readjusted, as well as the gauge.

108. Q. What is the cause of failure with the second injector, and what
should be done to obviate this failure?

A. Lack of attention and failure to use every day will allow joints to
work loose and boiler check to fill up with mud and scale. It should be
tested every day and worked regularly so as to keep it in good working
order.

109. Q. If an injector stops working while on the road, what should you
do?

A. Would first ascertain if sufficient water was in the tender and
tender valve open, and that water was cool enough in the tender so the
injector would handle it. Would next see that no obstruction was in the
feed pipe or strainer and that the feed pipe was free from leaks, and
that the injector was getting a sufficient supply of steam. If the
injector would not prime, would see whether overflow or heater valve
could open wide, or if overflow pipe was obstructed. If suction pipe was
very hot would blow water back into tank and let suction fill with cold
water. If possible, examine for obstruction in the steam priming tube
and water tubes. If it would prime and fail to deliver water to the
boiler, would see that the delivery tube was not obstructed and then
look for trouble at the boiler check. An obstruction in the tubes would
stop the injector working at once, while wear of the tubes or filling up
with scale would affect the injector gradually.

110. Q. What are the advantages of the combination boiler check and stop
valve?

A. A combination boiler check is fitted with a valve similar to a globe
valve and can be closed at will. Its advantage is that the boiler
pressure can be shut off from the check and the valve repaired without
cooling the boiler. This hand-operated valve can be closed to prevent
the boiler water passing back in case the check valve sticks up and
allows the boiler water to pass back to the injector when not working.

111. Q. How can a disconnected tank valve be opened without stopping?

A. Close the overflow or heater valve and turn steam back toward the
tank; this will usually lift the valve from its seat or turn it around
so it opens.

112. Q. What comprises the steam heat equipment on a locomotive?

A. A globe valve throttle at the boiler, a reducing valve, a steam gauge
connected to the steam heat pipe and the proper piping and hose
connections.

113. Q. What pressure is carried in the steam heat pipe, and how is it
controlled?

A. From twenty to sixty pounds in the train pipe, depending on the
length of the train, and is controlled by the regulating valve.

114. Q. What would you do in case the regulating valve failed to
operate?

A. In case the regulating valve would not admit sufficient steam to the
train pipe, would take it apart and block the steam valve open. If the
pressure ran up too high in the steam heat train pipe, would control it
with the steam throttle at the boiler head.

115. Q. How does the steam heat reducing valve control the pressure?

A. The inlet valve for live steam is opened and closed by the movement
of a metallic diaphragm in the valve which is opened by spring pressure
on one side and closed by steam pressure on the other side. To regulate
this pressure, stiffen the spring to carry more, weaken it to carry less
by turning the handle connected to this spring either up or down.

116. Q. If steam heat gauge showed the required pressure and cars were
not being heated properly, how would you proceed to locate the trouble?

A. First note where the hand on the steam heat gauge stands when steam
is shut off; if it does not drop back to zero see how much it lacks of
this and note the rise of pressure shown by the gauge when steam is
turned on. This is to test the gauge. If gauge is not correct, pay no
attention to it, but send back steam enough to heat the train. Over
sixty pounds will usually make the hose couplings on the cars rise up
and leak at the joints.

117. Q. When engine is detached from the train, what precaution should
you take to prevent freezing of the steam heat train pipe? What to
prevent damage of steam heat hose?

A. Open steam throttle to allow a very little steam to pass into steam
heat train pipe to prevent its freezing. If end of hose is liable to
strike frogs or crossings, hang it up where it will be safe.

118. Q. What constitutes abuse of an engine?

A. Improper use of injector by filling boiler at a rapid rate when
drifting or standing in a siding, unless you have a heavy bright fire to
heat the injected water to the boiler temperature as fast as it comes
into the boiler. Excessive use of the blower, especially with a light
fire or when cleaning the fire. Improper attention to machinery, such as
keeping parts not properly lubricated, rods not properly keyed, wedges
not adjusted, carrying too much or too little water in the boiler,
working water through the cylinders, allowing engine to slip
unnecessarily, use of sand on one rail only or otherwise improperly;
being careless in any way where care is required and not properly
reporting the necessary work so it can be done promptly.

119. Q. How are accidents and breakdown best prevented?

A. By inspection both at and after leaving terminals, frequently while
on the road, keeping all parts properly adjusted, water in the boiler at
the proper level and using good judgment in the handling of the engine
and train. It is much better to use care and prevent accidents than to
make repairs after they occur.

120. Q. What are the duties of an engineman when leaving his engine at
the terminal?

A. Place her on the proper track to be turned over to the hostler, leave
throttle closed securely, reverse lever in center notch, cylinder cocks
open, and lubricator feeds to steam chest and cylinders closed. The
boiler should be full of water and sufficient fire to maintain steam
pressure until fire is knocked out. Call fireman's attention to anything
of special importance. Inspect the engine very thoroughly, ascertain
whether any tools or signals have been lost on the trip and make a full
report of the condition of the entire locomotive.

121. Q. What is the most important bolt or nut on the locomotive?

A. The loose one. It should be cared for immediately.

122. Q. In reporting work on an engine, is it sufficient to do it in a
general way, such as saying: "Injector won't work," "lubricator won't
work," "engine won't steam," "engine blows," etc.? Or would you report
each special defect so it could be located after the engine was put in
roundhouse or on designated track whether it had steam pressure in
boiler or not?

A. No. Report all defects noticed so plainly that they can be located by
the repair man without unnecessary work and whether there is steam in
the boiler or not at the time repairs are to be made. If the engine
blows, make a test to locate the blow and report it correctly. Also
report any unusual feature in the operation of the engine during the
trip.



=COMPOUND LOCOMOTIVES=


1. Q. Wherein do compound locomotives differ from ordinary or simple
ones?

A. Simple engines take live steam from the boiler and after one
expansion in a single cylinder it is exhausted to the atmosphere. A
compound engine has two cylinders, sometimes one on each side of the
locomotive; other types have four cylinders or two on each side of the
locomotive. The live steam first passes into one cylinder, expanding
down for a portion of its pressure, and then being allowed to pass into
the second cylinder where it expands a second time, thus getting two
expansions from each volume of live steam. Both simple and compound
locomotives consist of two engines coupled to the same set of driving
wheels. Balanced compounds have four sets of main rods and crank pins.
Mallet compounds have two complete sets of engines under one boiler.

2. Q. Why is one cylinder on a compound locomotive called the
high-pressure cylinder and the other one a low-pressure cylinder?

A. The high-pressure cylinder takes that name because it works live
steam direct from the boiler at high pressure. The low-pressure cylinder
receives the steam after the first expansion and works with a low
pressure. It is always larger than its companion high-pressure cylinder
in order to get the same power from the low-pressure steam.

3. Q. In the Schenectady two-cylinder compound, what is the duty of the
oil dash-pot?

A. It is intended to prevent the too rapid movement of the intercepting
valve which might damage the valve or seat, and it is necessary that the
dash-pot should be full of oil to make it work properly.

4. Q. Explain how a Schenectady two-cylinder compound may be operated as
a simple engine.

A. To operate the compound as a simple engine, the separate exhaust
valve is opened which will cause the intercepting valve to move and stay
in position to allow the high-pressure cylinder to exhaust direct to the
atmosphere and admits live steam at a reduced pressure to the
low-pressure cylinder. This should be done when starting a train or when
moving very slowly and about to stall on a grade. The engine should not
be operated simple while running except when at low speed.

5. Q. Explain how a two-cylinder compound is changed from simple to
compound.

A. Place the handle of the three-way cock or simpling valve in the cab
so as to release the air from the cylinder of the separate exhaust
valve. A coiled spring will then close this valve. This permits the
exhaust steam of the high-pressure cylinder to accumulate in the
receiver until sufficient pressure is obtained to force the intercepting
valve into compounding position. This shuts off live steam from the
low-pressure cylinder and allows exhaust steam from the high-pressure
cylinder to feed through the receiver into the low-pressure steam chest.

6. Q. How should a compound engine be lubricated?

A. One-third more oil should be fed to the high than the low-pressure
cylinder, using more oil at high speed than at slow.

7. Q. Why feed more oil to high than to a low-pressure cylinder?

A. Because some of the oil from the high-pressure cylinder follows the
steam into the low-pressure cylinder.

8. Q. How would you lubricate the valve of low-pressure cylinder if the
oil feed became inoperative on that side?

A. Feed an increased quantity through the oil pipe to the intercepting
valve. Shut the engine off occasionally and cut into simple position.
Oil will then go direct from the intercepting valve into the
low-pressure steam chest and cylinders. This would avoid going out on
steam chest to oil by hand.

9. Q. How much water should be carried in the boiler of a compound
locomotive?

A. A very moderate level, never allowing it to get so high that moist
steam will pass through the cylinders, because for satisfactory service
a compound engine should always have dry steam.

10. Q. How should a compound locomotive be started with a long train?

A. In simple position with cylinder cocks open.

11. Q. When drifting what should be the position of the separate exhaust
valve, the cylinder and port cocks?

A. Open position.

12. Q. What will cause two exhausts of air to blow from the three-way
cock or simpling valve in the cab when the engine is being changed to
compound?

A. A sticky exhaust valve. It does not move when air is first
discharged. The second exhaust comes when it does move.

13. Q. What does steam blowing at the three-way cock indicate?

A. The separate exhaust valve not seating properly caused by stuck
valves, a weak or broken spring, or the packing rings of separate
exhaust valve leaking.

14. Q. What can be done if the engine will not operate compound when the
air pressure on the separate exhaust valve is released by the three-way
cock?

A. The separate exhaust valve has failed to close. Try jarring it with a
hammer on the front side, near the exhaust valve. With a bad case, take
the valve out, clean it and replace, if not broken.

15. Q. If the engine stands with high-pressure side on the dead center
and will not move when given steam, where is the trouble, and what may
be done to start the engine? Why?

A. The intercepting valve is stuck in compound position, so live steam
cannot get to the low-pressure cylinder. In a case of this kind, close
the throttle, open cylinder and port cocks; when all pressure is
relieved, use a bar to move forward the rod that works through the oil
dash-pot, thus moving the valve to simple position and steam will pass
to the low-pressure cylinder as soon as throttle is open. The engine
will not start, because with the low-pressure piston on the quarter,
steam must be admitted to its cylinder to start the engine.

16. Q. In the event of a breakdown, how should one disconnect?

A. The same as a simple engine with separate exhaust valve open, so
engine will work simple instead of compound.

17. Q. What may be done to shut off steam pressure from the steam chest
and low-pressure cylinder?

A. To shut off steam from the low-pressure chest, pull out the rod that
runs through the dash-pot as far as possible and fasten it in this
position. Then open the separate exhaust valve.

18. Q. Is it important that air be pumped up on a two-cylinder compound
before the engine is moved? Why?

A. Yes. Because the separate exhaust valve is opened by air pressure and
the engine cannot be simpled without sufficient pressure.

19. Q. How are the blows in a compound located?

A. The same as in a simple engine with the exception that any blow on
the high-pressure side will not be heard when the separate exhaust valve
is closed. A blow on the high-pressure side will increase the pressure
in the low-pressure side, so relief valves will pop on low-pressure side
when working compound with full throttle.

20. Q. What should be done if high-pressure piston of a cross compound
is broken off the rod, or if the high-pressure or low-pressure cylinder
head is broken?

A. Cover the ports on that side, open separate exhaust valve and run in;
use live steam in low-pressure cylinder only, for the broken piston.
With broken cylinder head, would cover ports on that side. Open separate
exhaust and run in with low-pressure side. Would not take down main rod,
but would take out pop valves in both cylinder heads and see that the
cylinder is properly oiled. For low-pressure head broken, would cover
ports on that side, open separate exhaust valve and use high-pressure
side; need not take down main rod, but would see that the cylinder is
well oiled.

21. Q. In the event of separate exhaust valves failing to work when
throttle is wide open, what can be done to assist in opening?

A. Ease throttle off very fine to reduce the receiver pressure; in a
moment or two the separate exhaust valve should then move. If this did
not work, would shut off entirely, even at the risk of stalling, as in
that event the train could be started again with engine cut in simple.

22. Q. If a transmission bar on a cross compound is broken, what would
you do for the right side? For the left side?

A. For right side would cover ports on that side, take out pop from
cylinder head, open separate exhaust and run in with other cylinder. For
left side, cover ports and fasten valve stem same as for right side.
Would leave main rods up, keep separate exhaust open in both cases and
see that cylinder is well oiled.

23. Q. In the event of a cross compound beginning to jerk badly and
cylinder head pops in low-pressure cylinder popping, where would you
look for the trouble?

A. That either the high-pressure valve or piston packing was blowing
live steam into the receiver and then into low-pressure steam chest. If
possible would locate trouble and report accordingly.

24. Q. If during a trip you found the piston valve rings of a cross
compound were broken, what would you do?

A. If nothing but rings were broken, would reduce boiler pressure about
25 per cent. and go on with my train if possible.

25. Q. If piston valve on cross compound was broken so it became
necessary to remove it, what should you do?

A. Remove the broken piston valve, reduce boiler pressure to 100 pounds
and proceed.

26. Q. What is the difference between a Vauclain four-cylinder compound,
a four-cylinder tandem, a balanced and a Mallet compound in their
arrangement of cylinders?

A. A Vauclain compound has two cylinders on each side, one above the
other, and both piston rods connected to one cross-head. A four-cylinder
tandem has four cylinders, the high pressure being ahead of the low
pressure on each side, and both pistons connected to one piston rod and
one cross-head. A balanced compound has four cylinders, the two
high-pressure cylinders being between the frames, each having a main rod
connected to a crank axle. The two low-pressure cylinders are located
outside the frame, each having a main rod and crank pin connected to
the driving wheel center. A Mallet compound consists of two separate and
independent engines, one fixed to the boiler, the other swinging from a
center and sliding back and forth under the front end of the boiler. The
rear engine works steam at high pressure; steam from this engine
exhausts through a receiver pipe having flexible joints to the forward
engine which works the steam at low pressure, then exhausts it to the
front end and stack.

27. Q. How many main steam valves has each type?

A. The Vauclain has one valve on each side, distributing steam to the
high and low-pressure cylinder on that side. The four-cylinder tandem
has two valves on each side, one for each of the two cylinders. A
Baldwin balanced compound has two valves the same as the Vauclain. The
American balanced compound has four valves, one for each cylinder, the
two valves for one side of the engine being connected to one valve rod.
A Mallet compound has a separate valve for each cylinder the same as a
simple locomotive.

28. Q. How do you test for blow in high and low-pressure cylinder
packing for each type of compound engine?

A. Simple the engine if a cross compound, then make test the same as for
a simple engine. For Vauclain four-cylinder compounds, test low pressure
first. A blow past the low-pressure piston will show the same as on a
simple engine; a blow past the high-pressure piston will make the engine
stronger on that side when working a full throttle and the exhaust from
the low-pressure cylinder will be heavier. To test the valve on either
side, cover the ports. Broken packing rings in the steam valve will show
a blow in one position and be tight in another. For tandem compound, to
test high-pressure piston packing, stand engine on the top quarter,
lever in back gear, drivers blocked and starting valve closed; remove
back indicator plug or open back cylinder cock of high-pressure
cylinder. Steam coming from the back cylinder cock must get by the
piston packing or by-pass or starting valve. Now put reverse lever ahead
and try the other indicator plug or cylinder cock. If a leaky by-pass
valve in the front end is the trouble, no steam will come through. To
test the low-pressure piston packing, place the engine in the same
position, lever in position to admit steam into the front end of
high-pressure cylinder. Open starting valve, remove back indicator plug
of low-pressure cylinder and give engine steam; if steam comes from the
indicator plug opening or open back cylinder cock, either packing or
by-pass is leaking. To determine which one, put reverse lever in another
position, close back indicator plug and open forward one; if blow still
continues, the packing rings are leaking or else both by-pass valves.
Would then inspect the by-pass valves.

29. Q. How can the blow through sleeve packing between high and
low-pressure cylinder of the tandem compound be located?

A. Place the engine as before on the top quarter, put reverse lever in
forward gear, see that starting valve is closed, block the drivers or
set the brakes solid and open the throttle. Until the engine moves,
unless there is a leak, no steam can get into the front side of the
low-pressure cylinder. Remove the indicator plug in front end of the
low-pressure cylinder for this test.

30. Q. How test for piston packing blow with balanced compound?

A. For a Baldwin balanced compound to test the high-pressure piston
packing, place the engine with the outside main pin on that side of the
engine on the bottom quarter, the reverse lever in the forward notch,
starting valve closed, set the brakes solid or block the drivers, remove
the indicator plug in the front end of either the high or low-pressure
cylinder. With throttle open this will admit steam to the back end of
high-pressure cylinder. Steam coming out of this plug opening, will
indicate a leak past the piston or the high-pressure valve. If
uncertain, next test the high-pressure valve by moving the reverse lever
to the center notch. This should cover the ports and if the valve is
tight the blow will stop. To test the low-pressure piston, place the
engine in the same position with wheels blocked, starting valve open,
back indicator plug out; when throttle is opened, the leaky packing will
be shown by steam issuing from the plug opening. If uncertain, the valve
can be tested by bringing reverse lever to the center of quadrant, which
will spot valve over port and if it is tight the blow will stop. In any
compound engine a blow past the high-pressure packing tends to increase
the pressure in the low-pressure cylinder. A blow past the low-pressure
packing can always be heard at the exhaust, and is usually on both
forward and back strokes, while a blow past the by-pass valves or valve
bushings occurs at a certain part of a complete revolution only.

31. Q. In case it was necessary to disconnect on one side of a compound
engine, how would you cover ports and hold valves in position?

A. The easiest way is to clamp the valve stem to hold valve in mid
position; this should cover all ports. It may be necessary to take off
head of piston valve chest and block in there.

32. Q. Is it a disadvantage to work a compound engine in short cut-off?
Why?

A. Yes. If cut-off is too short the proper proportion of steam passing
the throttle will not get to the low-pressure cylinder. The work should
be divided between the two cylinders on same side.

33. Q. In what way do the Mallet or articulated compounds differ from
other steam locomotives in the distribution of the steam?

A. Mallet compounds have two separate and complete engines under one
boiler. The rear engine has a rigid connection to the back end of the
boiler; this engine works boiler steam direct the same as a simple
locomotive. Under the front end of the boiler is another engine so
constructed that the entire front engine can move from side to side
under the boiler, having a hinged connection at the front end of the
rear engine to allow the locomotive to pass curves more easily. The
front engine takes the exhaust steam from the rear engine through a
flexible pipe or receiver and works it through a larger set of cylinders
and thus compounds the steam. From the low-pressure cylinders the steam
is exhausted to the atmosphere through the stack.

34. Q. How do you get the use of both engines when starting a train?

A. To get steam into the low-pressure cylinders before the high-pressure
engine has exhausted, some types of the Mallet compound have a live
steam pipe with a valve in the cab to admit boiler steam to the receiver
pipe and thus get the use of the front engine in starting a train. The
American Locomotive Company articulated compounds have an intercepting
valve similar to the one used in the Richmond cross compound, located
between the exhaust passage of the rear engine and the flexible
receiving pipe of the front one. This intercepting valve when in SIMPLE
position, allows the high-pressure cylinders of the rear engine to
exhaust directly to the stack instead of into the receiver, and feeds
boiler steam at a reduced pressure into the receiver pipe for the
low-pressure cylinders without giving any back pressure on the
high-pressure pistons. This increases the power of the complete
locomotive about 20 per cent. When in compound position, the
intercepting valve cuts off the supply of live steam to the receiver
pipe and forces the exhaust steam to go to the low-pressure engine
ahead.

35. Q. How is the American articulated compound changed from compound to
simple, and back to compound again?

A. To work the locomotive simple, place the handle of operating valve in
the cab to point toward the rear. This admits steam against the piston
that operates the emergency exhaust valve and opens it. Exhaust steam
from the high-pressure engine can pass to the exhaust nozzle instead of
to the low-pressure engine. The intercepting valve then moves over so
that live steam reduced to 40 per cent. of boiler pressure goes through
the receiver pipe to the low-pressure engine. To work compound, place
the handle of the operating valve to point forward. This will exhaust
the steam, holding the emergency exhaust valve open; a spring and the
pressure of the steam exhausted from the rear engine will close the
emergency exhaust valve and build up a pressure against the
intercepting valve that will open it so exhaust steam from the rear
engine will go to the forward one and at the same movement close the
reducing valve so no more live steam goes to the receiver.

36. Q. When is it necessary to use the operating valve to change the
locomotive from compound to simple, or from simple to compound?

A. When giving the engines steam to start, the intercepting valve should
automatically go to simple position until exhaust steam from the rear
engine builds up a receiver pressure that shifts the valve to compound;
if it does not, use the operating valve. When moving less than four
miles an hour or when about to stall on a grade, set the engines working
simple; changing to compound when the danger of stalling is over or the
speed is more than four miles an hour. If there is no intercepting valve
to furnish live steam to the forward engine, open the starting valve to
admit live steam to the receiver pipe and low-pressure engine.

37. Q. If in starting the locomotive the forward engine does not take
steam, what is the trouble?

A. The reducing valve may be stuck shut on account of being dirty or
stuck on the stem of the intercepting valve. In case the reducing valve
is stuck shut, the head of the dash-pot can be taken off and the valve
worked back and forth to loosen it. The intercepting valve should be
liberally oiled just before starting and occasionally during long runs
to keep it free from sticking.

38. Q. Why does the Mallet compound have more power when working simple
than compound?

A. If a starting valve is used to admit live steam to the receiver pipe
and thence to the low-pressure engine, this gives a higher pressure to
the low-pressure cylinders. If an intercepting valve is used, the open
emergency exhaust valve allows exhaust steam from the rear engine to go
direct to the stack; this takes away the back pressure of the receiver
steam from the high-pressure pistons, about 30 per cent. of the boiler
pressure, and thus adds to the power of the rear engine. The reducing
valve when feeding live steam gives about 40 per cent. of boiler
pressure to the low-pressure engine instead of the 30 per cent. it gets
from the receiver; the added power of both engines working simple is
about 20 per cent. over the compound operation.

39. Q. What is the duty of the by-pass valves on
the sides of the low-pressure cylinders? Should they be kept clean of
gum and grit?

A. These valves are connected to the steam ports at each end of the
cylinders and open to allow air and steam to pass from one end of the
cylinder to the other; away from the moving piston when the engine is
drifting. If not kept clean they may stick open; when working steam the
engine will blow badly; if they stick shut the engine will pound when
drifting.

40. Q. In what position should the reverse lever be when the steam is
shut off and the engine drifting?

A. Below three-quarters of full gear, so the valves will have nearly
full travel.

41. Q. Why should the power reversing gear of the Mallet compound always
have its dash-pot cylinder full of oil?

A. To prevent the too rapid movement of the reverse gear piston and its
damage.

42. Q. In what position should the engines stand to test for blows in
valves and piston packing?

A. Put the operating valve, or starting valve, in simple position. Spot
the engine in the proper position and test each engine for blows the
same as for a simple engine.

43. Q. What power is used with Ragonnet or Baldwin power reverse gear?

A. Air pressure.

44. Q. Can and should steam pressure be used?

A. Yes. However, steam should never be used except in an emergency when
air is not available.

45. Q. What precaution should be taken regarding steam check and
throttle?

A. That they are tight and check working properly, to insure that steam
is kept from entering main reservoir, for if it should do so it would
burn out the gaskets in the air brake equipment, allow moisture to
accumulate, which would result in freezing and bursting of equipment as
well as being dangerous.

46. Q. What would cause the gear to fail to hold links in intended
cut-off, and allow them to raise and lower without operating valve in
the cab being changed?

A. Leaks in main valve and piston packing.



=WALSCHAERT AND BAKER-PILLIOD VALVE GEARS=


1. Q. Give a brief explanation of the Walschaert valve gear.

A. The Walschaert gear has an eccentric crank attached to the end of the
main pin on each side of the locomotive, with an eccentric rod from this
pin to the connection at the bottom end of the link. This eccentric is
located so it serves for both forward and back motion. The link swings
on a center trunnion and cannot be moved up and down as the Stephenson
link, but the link block can be moved from one end of the link to the
other to reverse the engine; or part way toward the center of the link
to change the cut-off. A radius rod connects the link block to the valve
stem. There are two motions given to the valve stem, one from the link
block which regulates the travel of the valve for the cut-off and
reversing; the other motion is from a connection with the cross-head
which gives the valve a positive motion to take care of the lap and
lead. To give this motion there is used a combination lever or a lap and
lead lever connected to a cross-head arm by the union link.

2. Q. Is the Walschaert gear direct or indirect?

A. It is direct when the link block is below the center of the link; it
is indirect when the link block is above the center of the link.

3. Q. What are the principal differences in the location of the
Stephenson and Walschaert gears, and what advantages does this give the
Walschaert?

A. The Stephenson gear is placed between the main frames and employs two
eccentrics, with straps and rods on each side of the locomotive; one
for forward and one for backward motion. The Walschaert gear is placed
outside the driving wheels and frame, has but one eccentric, which is a
simple arm connected to the outside end of the crank pin for both
forward and back motion. The links are set above the wheels on a level
with the steam chest, the combination lever next to the cross-head. This
gives it an advantage of a better chance to inspect all parts, the
eccentric connections are much lighter and direct, which makes them less
liable to wear or breakdown, and the valve has a constant lead.

4. Q. How is the lead affected by movement of the reverse lever with the
two gears?

A. With the Stephenson gear the lead increases as the reverse lever is
hooked toward the center in both forward and back motion. With the
Walschaert gear the lead is the same in all positions of the lever, so
that the lever is used to reverse the engine or adjust the cut-off.

5. Q. In reversing, how do the two gears differ as to the movement of
the link and link block?

A. With the Stephenson gear, when reversing, the link is raised and
lowered, bringing the block which is not moved by the reverse lever
under control of either the forward or back-up eccentric as is desired
to move the engine the proper way. With the Walschaert gear the link is
not moved by the reverse lever, but the link block is raised and lowered
in the link; the position of the block above or below the center of the
link controlling the direction of motion.

6. Q. What would you disconnect if the eccentric crank, eccentric rod,
or the arm at the bottom of the link should break?

A. Would remove the broken parts, disconnect the link lifter from the
radius rod and block the link block in the center of the link; the
combination lever would then move the valve twice the amount of its lap
and lead, which would be sufficient to provide for lubricating the
cylinder.

7. Q. If the main crank pin was broken?

A. Take down eccentric rod, eccentric crank, main rod and all connecting
rods, block cross-head, disconnect from end of radius rod, chain it to
running board and block steam valve to cover ports.

8. Q. Broken cross-head pin, main rod, strap or brasses?

A. Take down main rod, block cross-head, disconnect front end of radius
rod and chain to running board and block the valve to cover ports.

9. Q. With a broken combination lever, union link or cross-head arms,
what would you do?

A. Would disconnect the forward end of the radius rod and secure it to
the running board with a small chain, wire or rope, remove all broken
parts, take off the combination lever, even if not broken, secure the
valve in its central position, loosen cylinder head to provide for
lubrication, leave up main rod and proceed on one side. If valve was
blocked to open rear port slightly, this would provide for lubrication
and the cylinder head need not be loosened.

10. Q. If the radius rod on Walschaert gear is disabled, what should be
done?

A. If broken in front of the link block, take off the broken part by
disconnecting from combination lever, take down eccentric rod, fasten
valve to cover ports and proceed on one side. If broken back of the
link block, block the link block in the desired position and proceed
with both sides.

11. Q. What would you disconnect with a Walschaert gear if a valve yoke
should break?

A. Disconnect the forward end of the radius rod, suspend it from running
board, block the valve, provide for lubricating the piston and proceed.

12. Q. How proceed with a broken reach rod?

A. Remove the reach rod, block links on lower side to hold them in
running position for proper direction. Unless radius rod lifters can be
uncoupled, leave a little slack in the blocking.

13. Q. How can you tell without opening the steam chest if the valve
covers the port with Stephenson gear? With Walschaert gear?

A. Place the rocker shaft vertical with Stephenson gear. Place the
combination lever vertical with reverse lever in mid gear so the link
block is in the center of Walschaert link.

14. Q. What is the Baker-Pilliod valve gear?

A. It is an outside gear with an eccentric crank, similar to the
Walschaert gear, but without a reversing link. The motion is reversed by
means of a reversing yoke instead of a link; the cut-off is changed in
the same manner. It uses a combination lever connected with a union link
to its cross-head arm. In case of breakdown remove the broken parts the
same as described for Walschaert gear, blocking the reversing yoke, if
necessary, in the proper position.

15. Q. Is the Baker gear a direct or an indirect motion?

A. It is direct, going ahead for an inside admission and indirect
backing up, and just the opposite for the outside admission type.

16. Q. What parts of the Baker gear take the place of the link which is
used by the Stephenson or Walschaert motion?

A. The radius bars and reverse yoke.

17. Q. What relation to the main pin is the eccentric crank set to?

A. The eccentric crank always follows the main pin.

18. Q. Should the eccentric rod or eccentric crank break how is the
engine put in condition to proceed?

A. The disabled side can have lap and lead travel and a port opening
equal to the lead for all cut-offs. First block the bell crank by using
a "U" bolt (which should be provided) in the holes placed in the gear
frame for this purpose. Throwing reverse lever in mid-gear will help to
get bell crank in position to block. Second, take down broken parts.
Third, knock out back pin of short reach rod and throw reverse yoke in
forward motion against gear frame.

19. Q. What is to be done should a gear connection rod break?

A. Do the same as for a broken eccentric or crank.

20. Q. What is to be done should the upper part of gear connection rod
break?

A. If break is close to the middle pin, do the same as for a broken
eccentric rod and also tie lower end of gear connection rod to keep it
from swinging. If break is near the top and below the jaw, first block
the bell crank and wire the connection rod fast to radius bars. If break
is through top jaw, do the same as for broken eccentric rod.

21. Q. What is to be done should a radius bar break?

A. Do the same as for broken eccentric rod.

22. Q. If the horizontal arm of bell crank should break?

A. Same as broken eccentric rod.

23. Q. What is to be done should the vertical arm or bell crank break?

A. Take down union link combination lever and valve rod, then block
valve over ports by using set-screw in valve stem cross-head provided
for that purpose.

24. Q. Should you break cross-head arm or union link, what would you do?

A. If rod be provided to secure lower end of the combination lever to
guide yoke, remove broken parts and proceed with full train, working
engine at long cut-off. Otherwise would remove broken parts, combination
lever and valve rod, cover ports, and proceed on one side.

25. Q. What do you do if a union link should break?

A. Same as for a broken cross-head arm.

26. Q. What is to be done if a combination lever should break?

A. Tie combination lever plumb, same as for a broken cross-head arm, if
it is possible. If not possible, take down the combination lever and
valve rod and cover the ports.

27. Q. What is to be done if a valve rod breaks?

A. Take down the broken parts and cover ports, leaving the rest of the
gear intact.

28. Q. What is to be done if a reverse yoke breaks?

A. If lugs for holding reach rod breaks, block yoke securely at whatever
cut-off you wish to work the engine and take down the short reach rod.
If break is below the lugs, do the same as for broken eccentric rod.

29. Q. What do you do if reach rod should break?

A. If short reach rod breaks, block the yoke at cut-off desired and wire
fast so it cannot move. If main reach rod breaks, block between tumbling
shaft arm and cross-tie brace, wiring same securely.

30. Q. What is to be done if the engine breaks down other than valve
gear?

A. In this case do the same as for any other valve.



=SOUTHERN VALVE GEAR=


1. Q. If the eccentric crank or eccentric rods fail?

A. Disconnect the eccentric rod from crank, radius hanger and
transmission yoke, tie up the hanger and yoke, clamp valve central
position and proceed.

2. Q. If radius hanger fails?

A. Disconnect the hanger from rod and take down eccentric rod, clamp
valve in central position and proceed.

3. Q. If transmission yoke fails?

A. Disconnect from the eccentric rod and clamp valve in central position
and proceed.

4. Q. If horizontal arm of bell crank fails?

A. Disconnect the yoke from the eccentric rod, tie up to clear, clamp
valve in central position and proceed.

5. Q. If vertical arm to bell crank breaks?

A. Clamp valve in central position and proceed. Take the broken arm down
if necessary.

6. Q. If one auxiliary reach rod or reverse shaft arm fail?

A. Block both link blocks in same position of links, and in such a
position as to give port opening enough to start train and control speed
by throttle.

7. Q. If main reach rod, or middle arm to reverse shaft fail? If both
auxiliary reach rods fail?

A. Block link blocks in full valve travel, controlling power and speed
with the throttle.



=LUBRICATION=


1. Q. What produces friction, and what is the result of excessive
friction?

A. Friction as considered in locomotive service is produced by one body
being rubbed across the surface of another when they are held in
contact by pressure, and the result of excessive friction is heat more
or less intense and the destruction of the journal and its bearing or
the roughening of the sliding surfaces.

2. Q. What is lubrication and its object?

A. The object of lubrication is to interpose a film of oil, grease or
some lubricant between the two surfaces that will prevent these rubbing
surfaces from coming into too intimate contact.

3. Q. What examinations should be made by the engineer to insure
successful lubrication?

A. See that all oil holes are open, cups filled and in good working
order, the packing in cellars evenly put in and in contact with the
journal. That waste on top of driving or truck boxes is in proper shape,
also that grease cups are filled, and the plugs and jam nuts in good
shape, and that the grease cellars contain sufficient grease for the
next trip.

4. Q. How should feeders of all oil cups be adjusted?

A. To feed as small a quantity of oil as possible and regularly to give
perfect lubrication.

5. Q. Why is it bad practice to keep engine oil close to boiler in warm
weather?

A. The oil is thinned to such a degree by the heat of the boiler that it
runs off as soon as applied, and very often a hot bearing is the result.

6. Q. In what manner would you care for a hot bearing if discovered on
the road?

A. Use as much time as available in cooling the same, making sure that
all moving parts are free and carefully lubricated before proceeding.

7. Q. What kind of oil should be used on hot bearings?

A. Use engine oil unless the temperature of bearing consumes it, when a
small quantity of valve oil may be used while the bearing is warm enough
to make this oil flow. The valve oil must be removed as soon as the
bearing cools to prevent reheating.

8. Q. At completion of trip what is necessary?

A. Close all adjustable feeds and examine all lubricated parts by
contact with the hand to determine that they are not above running
temperature.

9. Q. How would you determine what boxes to report examined? Why not
report all boxes examined?

A. By placing the hand on driving box, on hub of engine truck wheel and
on top of tender truck boxes nearest the brass, and would not report
them examined unless the temperature of same was above running heat. It
is not necessary to report all boxes examined, because they do not all
give trouble at the same time. If this report was made, it would appear
that a proper inspection had not been made and would result in
unnecessary work and waste of material.

10. Q. Why is it bad practice to disturb the packing on top of driving
and engine truck boxes with spout of oil can when oiling engine?

A. This packing is put on top of boxes to assist in keeping dirt and
dust out of oil holes, also to aid in gradual lubrication from the top.
If this packing is disturbed it will permit dirt and grit to work into
oil holes and on the bearings as well as feed the oil away too rapidly.

11. Q. How do you adjust grease cups as applied to rods?

A. Screw down plug until you feel a slight resistance from the grease,
stop when grease shows between brass and pin; this should be sufficient
over the division.

12. Q. Is it usual for pins to run warm when using grease?

A. Yes; grease does not work properly until it gets warm enough to flow
readily over the bearing.

13. Q. What effect does too much pressure produce?

A. Wastes grease and increases the friction until the surplus amount is
worked out so the bearing runs free on its journal.

14. Q. Is it necessary to use oil with grease on crank pins?

A. No.

15. Q. When an engine is equipped with Elvin driving box lubricator, how
can you tell whether a sufficient amount of lubricant is in the grease
receptacle?

A. The indicator wire fastened to the bottom of the grease cellar
indicates the amount of grease left in the cellar.

16. Q. Why should engine oil not be used on valves and cylinders?

A. Engine oil loses its lubricating qualities before it gets up to the
temperature of the valves and cylinders when they are working steam.

17. Q. At what temperature does engine oil lose its lubricating
qualities? At what temperature for valve oil?

A. Engine oil begins to separate and give off gas at 345 degrees F. The
temperature of steam at 120 pounds is 350 degrees F., while valve oil
has a flash test of 520 degrees F. The temperature of steam at 235
pounds is 431 degrees F., much lower than the flash test of valve oil.

18. Q. How and by what means are valves, cylinders and the steam end of
air pumps lubricated?

A. By a sight-feed hydrostatic lubricator.

19. Q. What is the principle on which a lubricator operates. How does
the oil get from the cup to the steam chest?

A. The lubricator is located in the cab so there is a gradual descent in
the oil pipe from the lubricator to the steam chest. Above the oil
reservoir is a condenser that is kept filled with water condensed from
steam fed from the boiler. The pressure of this water comes on the oil
in the oil tank below it, forcing oil through the sight-feed valves; it
then passes up by the sight-feed glasses to the oil pipe and steam
chest. The use of the glasses is to make the drop of oil visible as it
leaves the sight-feed nipple so the amount of oil fed can be regulated.
Steam from the boiler fed to the lubricator at boiler pressure through
the equalizing tubes balances the pressure which comes from the steam
chest when the engine is working steam.

20. Q. How should the lubricator be filled?

A. First close all valves connected with the lubricator, open drain plug
and remove filling plug, allowing water to escape until oil appears
with it. Drain plug should then be closed. Fill the oil tank in the
usual way, being careful not to overflow it; then replace filling plug.
If the supply of oil is insufficient to fill the lubricator, water can
be used to finish it, as the lubricator will begin feeding sooner when
filled full.

21. Q. After filling lubricator, what should be done?

A. Open the steam throttle to the lubricator wide, then carefully open
the water valve, but do not open the feeds until sure the chamber in the
glass is filled with water.

22. Q. How long before leaving terminal should the feed valves be
opened? Why?

A. About fifteen minutes; this time is necessary to allow oil to feed
through the oil pipe and reach the steam chests.

23. Q. How many drops should be fed per minute?

A. From one to seven, timed by the watch, depending on conditions.
Cylinders of large size require more oil than smaller ones.

24. Q. If lubricator feeds regularly when working steam and too rapidly
after shutting off, what is the trouble?

A. The opening in the choke plug at the lubricator or through the steam
valves at the steam chest is too large and should be reduced to the
proper size by applying new chokes or valves.

25. Q. When valves appear dry while using steam and the lubricator is
working all right, what would you do to relieve these conditions?

A. Ease off throttle for a few seconds to reduce the steam chest
pressure and drop the reverse lever a few notches to give the valve a
longer travel; oil held in the pipes will then flow down.



=FEDERAL REGULATIONS=

=For Inspection of Locomotive Boilers and Safety Appliances=


1. Q. What is the purpose of the federal rules and regulations for
inspection of locomotive boilers?

A. So that all railroads operating under the laws of the United States
government, would be obliged to maintain their boilers in a safe working
condition.

2. Q. What is the purpose of the quarterly and monthly interstate
inspection cards placed in the cab of the locomotive?

A. So that the federal inspector or engineer may see that the locomotive
boiler has received its monthly or quarterly inspection.

3. Q. What constitutes a safety appliance, as applied to a locomotive?

A. Any appliance that is placed on a locomotive for the purpose of
protecting the employees from personal injury.

4. Q. Name some of the safety appliances found on a locomotive?

A. Shield for tubular glass lubricators, also shields for water glass,
automatic couplers, with lever attachments, air brakes, etc.

5. Q. In what condition should safety appliances be maintained?

A. They should be maintained in first class condition.

6. Q. What should be done in event of any of the safety appliances being
damaged while engine is in service so as to render it unsafe?

A. Warn all employees whose duties require them to work around the
locomotive of its unsafe condition, then make report to those in
authority so that it may be taken out of service until repairs are made.

7. Q. What effort should be made on the part of the engineer to prevent
persons using a safety appliance which he knows is damaged and unsafe?

A. He should use such precaution as in his judgment would protect from
injury all persons who are on or around the locomotive.

8. Q. What is the duty of the engineer in event of his discovering a
safety appliance which is in an unsafe condition when taking an engine
from roundhouse territory?

A. He should report at once to the person in authority so that necessary
repairs may be made before engine goes into service.



=PYLE-NATIONAL ELECTRIC HEADLIGHT=


1. Q. Why are electric headlights applied to locomotives?

A. Electric headlights are applied to locomotives so that the engineer
may have a clear view of the track for enough ahead of the train to
enable him to protect the company's property in his charge.

2. Q. How far ahead of the engine should the arc headlight illuminate
the track?

A. Not less than from fifteen to twenty telegraph poles.

3. Q. State how you would focus the lamp.

A. First, would adjust back of the reflector so front edge of reflector
will be parallel with front edge of case. Second, adjust the lamp to
have point of copper electrode as near the center of reflector as
possible with carbons as near the center of the chimney holes as you can
set them. Third, have the locomotive on straight track. Now move the
base of the lamp around until you get a parallel beam of white light
straight down the center of the track, then tighten the lamp down.

4. Q. If the light throws shadows upon the track, is it properly
focused?

A. No.

5. Q. If the light is properly focused, that is, if the rays are leaving
the reflector in parallel lines, but the light does not strike the
center of the track, what should be done?

A. When the light rays are thrown out in parallel lines and they do not
strike the center of the track, it denotes that the headlight case is
not set straight with the engine, and the entire case on base board must
be shifted until the shaft of light strikes the track as desired.

6. Q. What can you do to insure a good and unfailing light for the
entire trip?

A. By carefully inspecting the entire equipment before departing on each
trip, and know that there are no wires with insulation charred or worn
off, that all screws and connections are tight, commutator clean and
brushes set in brush holder in proper manner. Carbon in lamp of
sufficient length to complete trip, and that the carbon will feed
through the clutch freely and rests central over the copper electrode.
Copper electrode cleaned off, oil in both bearings and see that steam
does not blow at stuffing box gland.

7. Q. What kind of oil and how much would you use in the bearings of the
electric headlight equipment?

A. Would use the best grade of black or engine oil furnished for both
bearings and only enough oil in oil cellar that the revolving loose oil
ring may trail through the oil. When bearings are supplied with oil
cups, use a heavy oil such as good engine or valve oil.

8. Q. Why should you not use valve oil in these bearings?

A. Valve oil cannot be used successfully in the main bearing because of
its heavy body. Valve oil could not be carried up to shaft by the oil
ring in cold weather, as the ring will not revolve.

9. Q. What is the most vital part of the dynamo?

A. The commutator.

10. Q. What care or attention should be given the commutator?

A. The commutator must be kept clean, free from dirt, and the mica must
be kept filed a trifle below the surface of the copper bars.

11. Q. What kind of a bearing should the brush have on the commutator?

A. Brushes should be fitted to have a bearing with the same contour as
the commutator.

12. Q. How are the brushes fitted?

A. Brushes are fitted by cutting a strip of No. 0 sandpaper about the
width of the commutator surface (have the dynamo idle), place the
strips of sandpaper under the brush, then pull the sandpaper from left
to right; continue this process until the brush has been fitted to a
true smooth bearing. Then trim about one-eighth inch off of the front
edge of the brush.

13. Q. Is it advisable to ever try to fit a brush with a file or knife?

A. Most emphatically no. You could not get a bearing across the brush no
matter how hard you might try with either a file or a knife.

14. Q. Why is it important to clean the scale off of the point of the
copper electrode each trip?

A. The scale on the copper electrode after it has cooled off is a
non-conductor of current, and acts as a blind gasket between the carbon
and the copper electrode. Unless this scale is removed, the current
cannot pass between the points of carbon and electrode and you cannot,
therefore, have a light. When the dynamo fields are compound wound, it
is unnecessary to clean scale from copper electrode oftener than once a
week, at which time copper electrode should be removed from holder and
all scale cleaned off. (With compound wound dynamo fields the cab lamps
will continue to burn when head-lamp is extinguished by lifting carbon
by hand.)

15. Q. How should the copper electrode be trimmed at the point?

A. The copper electrode should have about one-eighth inch surface on the
contact point.

16. Q. How far should the copper electrode project over the holder?

A. About one inch.

17. Q. Should the electrode be raised up to one and one-half inches,
what might happen?

A. If the copper electrode was run at a point so near the clutch, the
intense heat of the arc might do damage to the top carbon holder and
clutch.

18. Q. What regulation should be given to the tension spring No. 93 of
the lamp, and why?

A. This tension spring, No. 93, should be regulated when the current is
off the lamp and should be adjusted only tight enough to pull the magnet
yoke up against the top stop lug on the side of lamp column.

19. Q. If this tension spring was tightened too tightly, what might
happen?

A. At usual speed between stations, the movement of the engine would
impart an added resistance against the pull of the solenoid by the
tension spring, which would shorten up the arc and dim down the light.

20. Q. Is there anything else that could cause the light to dim down
when the engine is running fast?

A. Yes; if the spring No. 92-A that hold the heel of the clutch should
be too weak, the heel of the clutch would be forced up by the motion of
the locomotive; this would release the carbon which would fall to the
point of the copper electrode, causing the light to dim down, or, if the
clutch should be used until the sharp edge that grips the carbon should
have become worn smooth or round, the same would occur.

21. Q. If the light burns satisfactorily while the engine is in motion,
but goes out when engine is stopped, where would you find the trouble?

A. This trouble is most always found to be caused by the tension spring
No. 93 being too weak, though if the dash-pot plunger has become
corroded until it sticks in the dash-pot, the light will act the same as
if the tension spring were too weak.

22. Q. If the dash-pot should be found stuck, would you put oil in it?

A. Coal oil could be used to clean and cut the dirt out of the pot and
from off the plunger, but after the dash-pot and plunger have been
cleaned, all oil must be wiped off, for oil would cause the plunger to
stick as well as collect dirt.

23. Q. If the carbon of lamp should "jig or pound", what can be done to
stop it?

A. If the carbons pound the electrode, it is evidence that the iron
armature No. 64 may be too far out of the solenoid, or the speed of the
turbine engine may be too slow. This trouble can be remedied by adding
another link to the suspension link, which has one end connected to the
magnet yoke, the other end being connected to the iron armature No. 64.
If, however, when the arc is formed, it is found that the bottom end of
iron armature No. 64 measures one-half inch from bottom of solenoid, the
pounding is caused by the speed of turbine engine being too slow.

24. Q. If the copper electrode was fusing, how would you know it?

A. When the copper electrode is fused, a green light is always given
off.

25. Q. What should be done when a green light is seen?

A. Immediately close off on the steam throttle until a white light
re-appears.

26. Q. What is the cause of the fusing of the copper electrode?

A. Usually too high speed of the armature, although should you connect
the wires up wrong that the current flowing from the dynamo to the lamp
should enter the lamp at the electrode instead of passing through the
carbon first, you would get a green light and fuse the electrode.

27. Q. What arrangements have been made so that you cannot connect the
wires wrong?

A. The positive binding posts, both at the dynamo and the lamp, have
been provided with a much larger hole to receive the wire than has been
made in the negative binding posts, and the ends of the positive wire
should always be bent or doubled back, so that they will just enter the
receptacle in the positive binding posts, but cannot be connected at the
negative binding posts.

28. Q. Should the copper electrode and holder become fused until no
longer serviceable while on the road, what would you do?

A. Would remove the damaged holder from the lamp and substitute either
an iron bolt of sufficient length or a carbon, securing the improvised
electrode in the bracket of lamp same as the electrode holder is held,
only being sure that the end of the bolt or carbon comes up into the
center of the reflector and did not rest on the base of reflector or
lamp.

29. Q. What is the difference between a series wound equipment and a
compound wound equipment, and what advantages are obtained from the use
of the compound equipment.

A. With the series wound equipment, the incandescent cab lights burn
only with the arc lamp, while with the compound machine the incandescent
lamps are independent of the arc and can be used as desired.

30. Q. If you were running along with your light burning steadily and
nicely, then suddenly the light began to flash badly and kept it up,
where would you look for the trouble?

A. Trouble would usually be found at one of the binding posts, where one
of the binding post screws would be found loose.

31. Q. If you were running along with light burning satisfactorily and
suddenly it went out, where would you be likely to find the trouble?

A. You would find that either the carbon had burned out, one of the lead
wires had broken between the dynamo and the lamp, or one of the wires
had gotten loose at the binding post and fallen out.

32. Q. If the light goes out while you are between stations, what course
should an engineer pursue?

A. If the light goes out while you are between stations and an
investigation cannot be made within a few minutes thereafter to
determine the cause, the steam should be shut off from the turbine and
the dynamo stopped until such time when the cause of failure can be
determined.

33. Q. Why is it essential to shut off steam and stop the equipment?

A. For the reason that if the failure was due to a short circuit, damage
might be done to the coils or armature by overheating.

34. Q. How does the equipment act when short-circuited?

A. When there is short circuit, the engine will labor heavily, run slow
with a large volume of steam blowing at the exhaust, there will be no
light shown either at the arc or cab lamps, and the carbon point and cab
lights will only show a dull red or go entirely out.

35. Q. How will the equipment act when the circuit is broken, either by
a broken disconnected wire or a burned-out carbon?

A. With a broken circuit the engine will run noiselessly and fast with
very little steam blowing at exhaust and no light will be seen at the
arc or on cab lights.

36. Q. If the insulation on the cab wires is worn off until your two
wires can come together either directly or through the medium of some
metallic substance, what would occur?

A. A short circuit would result that would put out all of your lights.

37. Q. What should be done?

A. Wrap the exposed wire, if you can locate it, with a piece of waste,
or if you cannot locate the short circuit, disconnect one of your cab
wires from the dynamo. This would give you the benefit of the arc lamp
and you can look for the trouble at your leisure.

38. Q. If the light goes out when steam drops back fifteen to twenty
pounds, what is the trouble?

A. Either one of the governor valves is stuck shut, short bushing No. 18
in engine cab is worn badly, allowing wheel to drop away from the
governor stand so steam passes around wheel to exhaust, or governor
springs are too weak.

39. Q. In this case what should be done?

A. Report of the action of the dynamo should be made upon the work book
at the terminal.

40. Q. If clutch rod No. 78-B should break while on the road, what could
be done to get use of the lamp?

A. A piece of wire could be used by fastening one end around the end of
top lever No. 59, the other end being attached to clutch through eye.

41. Q. If you should lose the clothespin holder or top carbon clutch,
what could be done to get the light?

A. Would fasten a wire around the carbon and top holder to keep carbon
in line, being careful not to get the wire either too tight or too
loose.

42. Q. If you should lose the iron armature No. 64 in solenoid, what
could be done to get use of light?

A. Would use a common iron bolt and suspend same by wire in magnet.

43. Q. What would be the result if any of the levers of the lamp should
bind?

A. All levers of the lamp must work absolutely free and must not drag,
for if they are not perfectly free the carbon cannot feed properly.


=Pyle-National Electric Incandescent Headlight=

44. Q. What is meant by an incandescent headlight equipment?

A. A headlight having an electric incandescent lamp in the reflector in
place of the usual oil or acetylene gas flame, and electric instead of
oil cab lamps, the electricity being generated by a small combination
steam-turbine and electric generator. Suitable wiring distributes the
electric current.

45. Q. In what manner does the incandescent headlight differ from the
arc headlight?

A. It is not so powerful. An incandescent or bulb type of lamp takes the
place of the arc lamp in the headlight reflector. The current being less
than is required for an arc, is supplied by a smaller turbine.

46. Q. What type of incandescent lamp is used in the reflector?

A. A low voltage, gas filled bulb, containing a very compact or
concentrated fillament.

47. Q. Why cannot a standard or house type of lamp be successfully used
in the reflector?

A. Because the fillament or light-giving wire inside the bulb is not
sufficiently compact or concentrated to reflect the light in the form of
a beam. The voltage of the house lamp is also too high to be used on a
locomotive installation.

48. Q. How is the lamp held in place in the reflector?

A. By the usual socket, into which the lamp screws. The socket is a part
of the focusing device, one type of which holds the lamp in a horizontal
position, while in the other the lamp is held vertically or upright.

49. Q. Before turning the steam into the turbine, what precautions
should be observed?

A. The turbo-generator should be lubricated by a small amount of black
or engine oil, placed in the cup on the turbine or steam end. On the
generator end, the oil should be maintained within one-half inch of the
top of the hinge-cover cup; using black oil. The drainage of the steam
end is cared for automatically by a three-eighth inch drain pipe without
a valve. The pipe should be kept open.

50. Q. How do you proceed when you wish to use the light?

A. Open the globe valve in the steam pipe to the turbo-generator, at
least two turns. The water-glass, steam and air gauge lamps in the cab,
and the number indicator lamp in the headlight case should light up as
soon as the turbo-generator reaches full speed. A double-throw knife
switch in the cab controls the headlight. In one position the switch
gives the full brilliancy of the headlight. The opposite or "dimmer"
position reduces the brilliancy about one-half. When the switch bar is
in neither position the headlight is entirely out, and only the number
lamp is burning. The classification lamp, lubricator and order or
reading lamp, are controlled by a small switch on the socket of each
lamp.

51. Q. For what purpose is the dimmer, and how does it operate?

A. It is to reduce the intensity of the headlight when locomotive is in
yards or around stations. It consists of a small resistance tube in the
wiring circuit, and with the cab switch in dimmer position, a portion of
the current is converted into heat instead of light.

52. Q. How is an incandescent headlight focussed?

A. By moving the lamp in its position in the reflector until the most
brilliant and compact beam of light is obtained. If the beam does not
strike the track centrally, or as high or low, the headlight case must
be moved on its platform until the beam is properly directed. It is
often necessary to raise the front or back of the case by shimming
between the case and its platform in order to direct the beam of light
the proper distance ahead of the locomotive.

53. Q. What provision is made for moving or focussing the lamp in the
reflector?

A. When the lamp is mounted horizontally there are thumb screws by which
the lamp may be moved sidewise, up and down, and forward and backward.
This mounting is called the "micrometer" device, because of the accuracy
of adjustment. With the vertical mounting, a flat head thumb screw at
the base of the lamp support releases the ball joint so that the lamp
may be easily moved sidewise or forward and backward. To raise or lower
the lamp, the thumb screw higher on the lamp stand must be loosened.

54. Q. What causes a "black spot" in the illumination ahead of the
locomotive?

A. The lamp is out of focus, being too far ahead or back of the proper
position in the reflector.

55. Q. How would you remedy the following possible defects?

A. (a) =All lamps fail to burn.= If turbine is not running the wrong
steam valve in the cab may have been opened, or there may be a second
valve, closed, in the steam pipe. The screen on the governor valve in
the turbine may be clogged. Remove brass cap at top of turbine and
unscrew screen or strainer-cap.

(b) =Turbo-generator runs, but no lights.= Wires may be
"short-circuited" (crossed) which will cause brushes to spark badly, and
turbo-generator to pull hard. The "short" can usually be found by an
occasional sparking or smoke at the point of trouble. Separate and
protect wires when short is found. The brushes may be "cocked up" as
left by some repair man. Open the dynamo door and see that the brushes
bear on the copper commutator. A wire may be loose at the dynamo binding
posts (which may be seen when the dynamo door is open), or at the main
switch in the cab. A main wire may have broken. (All locomotives are not
equipped with fuse plugs.) A fuse plug may have become loose or burnt
out. Replace with new fuse plugs or break an incandescent lamp and twist
the leads in the base together, when the base may be screwed into the
fuse plug socket, answering the purpose of a fuse plug, temporarily.

(c) =Headlight fails to burn.= Examine the wires between cab switch and
head lamp for breaks or disconnections. Examine fuse plugs (which are
sometimes in head lamp circuit only) and proceed as in (b) if trouble is
found there. Headlight bulb may not be screwed in far enough to make
contact in the socket, as the lock-sockets provided to prevent lamps
loosening cause lamp to screw in hard. Lamp may have broken fillament.
Replace with proper type of lamp or use a cab lamp.

(d) =Lamps burn dim.= Steam valve not open wide enough. Boiler pressure
too low. Brushes sparking badly on commutator of dynamo--due to poor
contact. Governor or steam-valve of turbine improperly adjusted.

(e) =Lamps burn too brightly.= Improper turbine regulation. Throttle the
steam valve in cab until lamps are reduced to proper brilliancy. Report
all irregularities on arriving at terminal.



=SCHROEDER HEADLIGHT=


1. Q. What is the speed of a Schroeder headlight dynamo?

A. About 2,800 revolutions per minute.

2. Q. How is the speed altered?

A. By a governor in the turbine.

3. Q. How would you proceed to change the speed of the governor?

A. Remove cover No. 3 and loosen lock nut No. 14 and turn nut No. 13 to
the right to increase the speed and to the left to decrease it.

4. Q. What is a short circuit?

A. A connection between the positive and negative wires of the dynamo
without any resistance between.

5. Q. How does the dynamo act when short-circuited?

A. It will run very slowly as it is under a heavy strain.

6. Q. What would be the result if left to run under that strain?

A. The armature or fields would burn out.

7. Q. What would you do if a short circuit developed while on the road?

A. Shut the steam off and remove the positive or right-hand wire of the
cab circuit from the dynamo, start up and see if the headlight went to
work properly; if not, replace the cab wire and remove the positive or
left-hand wire and see if the cab lights burned properly. If such was
the case, let it run, using the small incandescent light in the case for
a headlight and report it at the roundhouse.

8. Q. What is a volt?

A. The unit of pressure of electricity.

9. Q. What is an ampere?

A. The unit of quantity of electricity.

10. Q. What is the proper voltage of a Schroeder headlight?

A. About 28 volts.

11. Q. Can a person be injured by that voltage?

A. No.

12. Q. What is the proper amperage of a Schroeder headlight?

A. About 30.

13. Q. How often should the ball bearings be oiled?

A. About three times a week.

14. Q. How often should the governor be oiled?

A. Before leaving every trip.

15. Q. What kind of oil should be used?

A. Valve oil.

16. Q. Is it necessary to clean the electrode every trip?

A. No.

17. Q. Why?

A. The dynamo is provided with shunt fields which build up the current
regardless of the arc light.

18. Q. What are the two causes of lamp burning green?

A. Speed too high, or wires to the lamp being reversed.

19. Q. If the carbons burned away too fast, but otherwise the lamp
appeared to be burning properly, where would you look for the trouble?

A. It would indicate that tripping spring No. 209 was too tight.

20. Q. If tripping spring No. 209 was being annealed from heat and
sparks were noticed at the clutch, where would you look for the trouble?

A. Flexible wire No. 251 would be broken.



="BUDA-ROSS" ELECTRIC HEADLIGHT=


1. Q. What are the three essential elements in the "Buda-Ross" electric
headlight equipment?

A. Steam turbine engine, dynamo directly connected on the same shaft,
and self-focusing arc lamp.

2. Q. At what speed should the turbine run?

A. 2,800 revolutions per minute.

3. Q. How is the speed controlled?

A. By a centrifugal governing device.

4. Q. How does the steam enter the turbine?

A. Through a main valve which is perfectly balanced in all steam
pressures directly and impinged on the buckets directly from a nozzle.

5. Q. About how much opening should this valve have?

A. About one-fourth of an inch.

6. Q. Can the lift of this valve be changed?

A. Yes.

7. Q. How?

A. By adjusting the inner sleeve of the valve with a common monkey
wrench after removing cap nut on top of turbine.

8. Q. Can this be done while the light is burning?

A. Yes.

9. Q. What is necessary to do this?

A. Take a monkey wrench and screw the inner sleeve down to the right to
reduce the lift, and to the left to increase the lift. In reducing the
lift you reduce the speed, and by increasing the lift you increase the
speed.

10. Q. Is there any other method of setting speed?

A. Yes.

11. Q. How?

A. By removing oil box on the turbine cap and adjusting the nuts on the
governor studs on the face of wheel.

12. Q. Is any provision made for operating the light with low pressure
steam?

A. Yes.

13. Q. What?

A. An auxiliary valve is used which operates automatically at any
predetermined pressure, which is adjusted by an adjusting stem at the
bottom of the engine and which can also be adjusted while the light is
burning.

14. Q. What kind of oil should be used in the "Buda-Ross" bearings?

A. Cylinder or valve oil.

15. Q. What style of generator is used.

A. An iron-clad type with no outside magnetism.

16. Q. How many fields in this generator?

A. Two.

17. Q. What style field is used?

A. Compound wound.

18. Q. What kind of wire is used on these fields?

A. Deltabeston wire.

19. Q. Why is Deltabeston wire used in preference to cotton-covered
wire?

A. So that it cannot be injured by short circuits, for if a short
circuit occurs and afterwards is removed there is no danger done to the
insulation on this make of wire.

20. Q. Where are the fields located?

A. One on each side of the dynamo.

21. Q. Why?

A. So that they cannot be injured by waste oil from the ball bearing, or
by water or snow.

22. Q. How should ball bearing on dynamo end be lubricated?

A. By removing oil plug in frame just back of dynamo and introducing
cylinder oil.

23. Q. Is it necessary to remove the top carbon holder from the lamp to
remove reflector from case?

A. No.

24. Q. Why not?

A. Because there is no top guide to the carbon, as the carbon is guided
by the clutches.

25. Q. How many levers are there in the lamp?

A. Only one.

26. Q. What regulation should be given to top lever spring No. 308 on
lamp?

A. Top lever spring No. 308 should be adjusted as loose as possible and
not have light go out standing still.

27. Q. If this spring was tightened until the light burned steady when
the locomotive was at rest, what might occur when engine was running
high speed?

A. It might cause the light to dim down.

28. Q. Is there anything else that would cause the light to dim down
when the engine is running fast?

A. If the clutches should be used until the sharp edge that grips the
carbon have become worn smooth or round they would allow the carbon to
feed too fast and the light would burn dim.

29. Q. If the light burns satisfactory while engine is in motion, but
goes out when engine is stopped, where would you find the trouble?

A. This trouble is most always found to be caused by the top lever
springs No. 308 being too weak; or, an imperfect carbon, though if the
dash pot plunger has become corroded until it sticks in the dash pot,
the light will act the same as if the tension spring was too weak.

30. Q. Is it possible to apply the bottom electrode holder wrong?

A. No

31. Q. Why not?

A. For the reason that its support is on a center line with the
electrode and the holder can be turned in any direction and the
electrode is held central with the top carbon.

32. Q. What would you do if you had no bottom electrode holder?

A. Place a piece of 5/8-inch carbon in the hole through the bottom
bracket having top end in focal point of reflector and tighten with
set-screw; as this carbon would burn away the light would be raised and
it would therefore be necessary to raise the carbon about every hour, as
the carbon would burn away about one-half inch per hour.



=GENERAL QUESTIONS AND ANSWERS ON ELECTRIC HEADLIGHTS=


33. Q. Describe the passage of the current through the lamp and tell how
arc light is formed?

A. It enters the lamp at the binding posts with the large hole, then to
the top carbon holder, carbon, then into the electrode and holder; from
there to the solenoid and back to the dynamo, leaving the lamp at the
binding post with the small hole in it. The magnetism from the current
while passing through the solenoid attracts magnet in a downward motion,
and it in turn, by the levers on the lamp, separate the carbon from the
copper, thereby forming the arc.

34. Q. Why should sandpaper be used to smooth commutator instead of
emery cloth?

A. In using emery paper a piece of emery might lodge in the grooves
between the commutator segments, and being a conductor of electricity,
causes short. Will also get embedded in the copper and cut the brushes.
Sand will not do this.

35. Q. State how you would go about to focus a lamp?

A. (1) Would adjust back of reflector so front edge of reflector would
be parallel with front edge of case. (2) Adjust lamp to have point of
copper electrode as near the center of reflector as possible with
carbons as near the center of chimney hole as you can set them. (3) Have
the locomotive on straight track. Now move the base of the lamp around
until you get a parallel beam of white light straight down the center of
the track, then tighten lamp down.

36. Q. If the light throws shadows upon the track, is it properly
focused?

A. No.

37. Q. If the light is properly focused, that is, if the rays are
leaving the reflector in parallel lines, but the light does not strike
the center of the track, what should be done?

A. When the light rays are thrown out in parallel lines and they do not
strike the center of the track, it denotes that the headlight case is
not set straight with the engine, and the entire case on baseboard must
be shifted until the shaft of light strikes the track as desired.

38. Q. What can you do to insure a good and unfailing light for the
entire trip?

A. By carefully inspecting the entire equipment before departing on each
trip and know that there are no wires with insulation chafed or worn
off; that all screws and connections are tight; commutator clean;
brushes set in brush holder in the proper manner; carbon in lamp of
sufficient length to complete trip; copper electrode cleaned off and oil
in both bearings.

39. Q. Why would you not fill the main oil cellar full of oil?

A. If you should fill the main oil cellar full of oil, the oil would run
out of the overflow holes on the side and all over the equipment and
locomotive and could do the dynamo no good but possibly harm.

40. Q. What is the most vital part of the dynamo?

A. The commutator.

41. Q. What care and attention should be given the commutator?

A. The commutator must be kept clean, free from dirt and grease; the
mica must be kept filed down about one-sixty-fourth of an inch below the
surface of the bars.

42. Q. How should you clean the commutator, and when?

A. The commutator should be cleaned before starting out on each trip by
using a piece of damp waste, rubbing the bars lengthwise, then wipe dry
with clean dry piece of waste.

43. Q. What kind of a bearing should the brush have on the commutator?

A. Brushes should be fitted to have a bearing with the same contour as
the commutator, with bearing covering no less than two of the commutator
bars, nor more than three of the bars.

44. Q. How are the brushes fitted?

A. Brushes are fitted by cutting a strip of No. O sandpaper about the
width of the commutator surface. (Have the dynamo idle.) Place the strip
of sandpaper under the brush on the commutator with the rough side
towards the brush, then pull the sandpaper from right to left; continue
this process until the brush has been fitted to a true smooth bearing.
Then trim about one-eighth of an inch off the front edge of the brush.

45. Q. Is it advisable to ever try to fit a brush up with a file or
knife?

A. No.

46. Q. Why is it important to clean the scale off the point of the
copper electrode each trip?

A. To allow the point of the carbon and the electrode to touch to form a
circuit; this scale being a non-conductor of electricity and with it on,
the current would not pass from the carbon to the electrode and holder.

47. Q. How should the copper electrode be trimmed at the point?

A. Copper electrode should have about 1/4-inch surface at contact point.

48. Q. How far should the copper electrode project above the holder?

A. One inch.

49. Q. Should the electrode be raised up to 1-1/2 inches, what might
happen?

A. If the copper electrode was run at a point so near the clutch, the
intense heat of the arc might do damage to the top carbon holder and
clutch.

50. Q. If the dash pot should be found stuck, would you put oil in it?

A. Coal oil should be used to clean and cut the dirt out of the pot and
from off the plunger, but after the dash pot and plunger have been
cleaned all oil should be wiped off of same, as the oil would cause the
plunger to collect dirt and stick.

51. Q. If one carbon of lamp should "jig or pound", what can be done to
stop it?

A. If the carbon jumps or pounds the electrode, it is evident that the
iron armature is too far out of the solenoid, or the speed is too low.

52. Q. Does the pounding of the lamp occur with the old series wound
machines or with the new compound wound machines?

A. The pounding of the lamp occurs with the new compound wound machines.

53. Q. If the copper electrode was fusing, how would you know it?

A. By the fact, when copper is fused a shaft of green light will be
thrown off instead of a shaft of white light.

54. Q. What should be done when a green light is seen?

A. Close the throttle to turbine engine, then open slowly until a white
light re-appears.

55. Q. What is the cause of the copper electrode fusing?

A. The cause of the copper electrode fusing is due to too high speed of
the generator, or having lead wires connected up wrong, allowing
positive current to get into copper electrode first.

56. Q. What arrangements have been made so that you cannot connect your
wires wrong?

A. The positive binding post both at the dynamo and lamp have been
provided with a much larger hole to receive the wire than has been made
in the negative binding post, and the ends of the positive wire should
always be bent or doubled back so they will just enter the receptacle in
the positive binding posts, but cannot be connected to the negative
binding post.

57. Q. Should the copper electrode and holder become fused until no
longer serviceable out on the road, what would you do?

A. Would remove the damaged holder from the lamp and substitute a
carbon, securing the substituted electrode in the bracket of lamp same
as the electrode holder is held. Be sure that the end of the carbon
comes up to center of reflector and does not rest on base of reflector
or lamp.

58. Q. If you were running along with your light burning steady and
nice, then suddenly the light began to flash badly and kept it up, where
would you look for the trouble?

A. You would no doubt find one of the lead wires loose in binding post.

59. Q. If you were running along with light burning satisfactorily and
suddenly your light went out, where would you be likely to find the
trouble?

A. You would undoubtedly find carbon burned out, or a lead wire was
broken off or out of the binding posts.

60. Q. If the light goes out while between stations, what course would
an engineer pursue?

A. If investigation cannot be made within a few minutes thereafter to
determine the cause, the steam should be shut off from the turbine
engine until such time when cause of failure can be determined.

61. Q. Why is it essential to shut off steam and stop the equipment?

A. If failure was due to a short circuit, damage might be done to the
armature or field coils by overheating.

62. Q. How does the equipment act when short circuited?

A. The engine will labor heavily and run slowly with a large volume of
steam blowing at the exhaust, the carbon points and cab lights will only
show a dull red light.

63. Q. How would you test for a broken circuit?

A. Would test for a broken circuit or open circuit: First, by placing a
carbon across the binding posts at dynamo. If the trouble was in the
dynamo, no flash would be seen, but if dynamo was all right you would
get a flash; this would indicate that the trouble was on towards the
lamp. Second: Go to the lamp, place your carbon across binding posts. If
wire was broken between dynamo and lamp you would not get a flash. If
your wires were all right you would get a flash and you would find your
trouble in the lamp. No doubt, it would be a burned-out carbon.

64. Q. How would you proceed to locate the point of trouble with a short
circuit?

A. Would remove (1) one of the lead wires from the binding post at
dynamo; if trouble was in dynamo you would not note any difference in
action of speed. (2) Would disconnect one of the cab wires; if the
trouble is in cab circuit, speed would increase and lamp would burn. (3)
If trouble is not in cab circuit, would go to lamp, disconnect one of
the main wires from binding post; if short circuit is in the wires
between dynamo and lamp, there would be no change in speed of dynamo,
but if the wires are O. K. the speed of engine would increase and your
trouble would be in the lamp.



=DUPLEX LOCOMOTIVE STOKER=


1. Q. Of what does the driving mechanism of a Duplex Locomotive Stoker
consist?

A. It consists of a steam cylinder with reverse head and valve
arrangement similar to the steam end of an eleven inch Westinghouse air
pump.

2. Q. How is the power controlled?

A. The speed is variable, and by turning the valve controlling the
engine steam inlet, can be made greater or less according to the amount
of coal needed.

3. Q. For ordinary operation, how much steam pressure is required?

A. About fifteen pounds, with piston strokes varying from 10 to 15 per
minute.

4. Q. How can the duplex stoker driving engine be started, stopped, or
reversed?

A. By means of operating and reversing rod, fastened to the back head
and connected with the valve on reverse head of engine cylinder.

5. Q. How can the conveying screws be started, stopped, or reversed
separately or together?

A. By ratchet and pawl arrangement controlling each.

6. Q. What practice should be followed in building up the fire before
leaving a terminal?

A. Build up a light even fire by hand and do not bring stoker into use
until the locomotive is working steam.

7. Q. How should the stoker be oiled and operated?

A. It should be thoroughly oiled before leaving the terminal, then see
that operating rod on back head is in center or running position, open
main jet line so they register about fifteen pounds on the jet steam
gauge if coal is coarse, or ten pounds if coal is small. Next, the
driving engine steam valve should be opened wide and the throttle valve
opened just enough to supply the proper amount of coal to the fire-box.

8. Q. How is the distribution of coal over the grate area accomplished?

A. By means of a low-pressure constant steam jet located in the back and
bottom portion of each distributor elbow, as indicated by its
individual pointer on steam gauge.

9. Q. By increasing the jet pressure, will more coal be carried to
forward end of fire-box and against the flue-sheet?

A. Yes, it will, and by decreasing the jet pressure more coal will be
fed at middle and back end of fire-box.

[Illustration]

10. Q. Can the fireman direct the even distribution of coal in the
fire-box?

A. Yes; by changing position of the dividing rib located in the transfer
hopper, and by moving the regulating lever to either side.

11. Q. Should the sliding plates at the bottom of the tank be closed
before coal is put on tank?

A. Yes, so that screw conveyor will not become clogged and inoperative.
Only one slide should be opened at a time and coal fed from tank as
required.

12. Q. In case the stoker becomes clogged or it is desired to reverse it
for any reason, what must be done?

A. The operating rod located on the back-head of the locomotive
boiler--if the piston is making a power stroke--should be moved to its
lower position, and if the piston is making a return stroke, it should
be moved to its upper position. This moves a small valve in the
auxiliary head, bolted to reverse head, and steam is admitted to
opposite head of cylinder, causing the piston to change its direction.
The return of the operating rod handle to a central position causes the
driving engine to resume its normal operation.

13. Q. How can the fireman observe the condition of fire in fire-box?

A. The elbows are provided with peep valves with swinging covers through
which the coal supply and condition of fire may be seen.

14. Q. Why are two gauges necessary?

[Illustration]

A. The driving engine gauge on the left indicates the pressure of steam
used by the driving engine. The one on the right has two indicators, the
red indicator showing the steam pressure on the jet in left elbow, and
the black indicator showing the pressure on the jet in the right elbow.

15. Q. When train is standing on siding for a short period, what should
be done?

A. Shut stoker off by throwing operating rod on back head of locomotive
boiler out of running position.

16. Q. When train is to stand for a long time or engine is left at
terminal, what should be done?

A. The driving engine should be cut out entirely by closing main steam
line inlet and main lubricator connection, and in winter time all drain
cocks should be opened.

17. Q. If sufficient coal can not be supplied over front grates, what
may be the cause?

A. Distributors may be warped and point too low, or steam jets may be
plugged with pipe scale and not blowing freely.

18. Q. How would you start and operate stoker?

A. First open main valve No. 1 at steam turret. Valve 2 is then opened;
this is the main valve in stoker steam line. Next open valve 3, which
allows the steam to flow to the distributor jet line; open valves 4 and
5, which govern the pressure on the jets until ten pound pressure shows
on the right-hand gauge. See valve 8 to the exhaust line is open, and
valve 9 to the transfer hopper is closed.

19. Q. How would you start the stoker engine?

A. Place operating lever 10 in horizontal or running position. Place
conveyor reversing lever 12 in forward position. Open valve 6, which
allows the steam to pass to the operating valve and starts stoker
running. Valve 7 is to be used as an emergency valve only in case of
clogging. Stoker should be run slowly at first. Do not feed too much
coal and carry a light fire.

20. Q. How would you reverse conveyor screw in tank?

A. Lower handle 10 on operation rod on boiler head to bottom position.
Move screw conveyor, reverse lever 12 back to rear or reverse position,
raise handle 10 on operating rod to center position.

21. Q. How would you stop conveyor screw in tank?

A. Place conveyor reversing lever 12 in center position.

22. Q. How would you reverse right or left elevator screw?

A. Raise elevator pawl shifter 26 on top of the vertical shaft to upper
position.

23. Q. How would you stop right or left elevator screw?

A. Raise elevator pawl shifter 26 on top of the elevator to middle
position.

24. Q. How would you locate clogs in case the stoker stalls?

A. First, shut off pressure to stoker engine cylinder by closing valve
6. Second, move operating valve lever 10 to its lowest position. Third,
place tender conveyor reverse lever 12 in center. Fourth, place right
elevator pawl shifter 26 in neutral position. Fifth, raise operating
valve lever 10 to center position. Sixth, open valve 6 sufficiently to
run left elevator to ascertain if it operates freely. Cut in right
elevator by lowering pawl shifter 26, and if stoker stops, the
obstruction is in the right elevator. If it continues to operate, then
the obstruction is in the tank conveyor.

25. Q. How would you remove clogs?

A. Clogs in upright elevators usually occur at the bottom. Raise the
door in the engine deck and remove the obstruction if in the elevator,
reverse the elevator screw forcing the obstruction back down in transfer
hopper. It may be a small mine spike lodged above this point, and by
removing the nut at top of elevator casing and removing the door the
obstruction can be easily removed.

26. Q. If the clog is in the tank conveyor, how would it be removed?

A. The clog will usually be found in the crushing zone. Reverse the tank
conveyor screw, forcing the obstruction back, when it can be removed
from the trough.

27. Q. How far should the conveyor screw be run backwards?

A. Not more than three revolutions.


[Illustration]

PARTS OF DUPLEX LOCOMOTIVE STOKER
1. Conveyor Trough.
2. Conveyor Screw.
3. Angle Ring.
4. Crusher.
5. Operating Head.
6. Driving Engine Cylinder.
7. Reverse Valve.
8. Piston Rod.
9. Transfer Hopper.
10. Left Elevator Casing.
11. Left Elevator Screw.
12. End of Elevator Screw Shaft.
13. Elevator Pawl Shifter.
14. Elevator Pawl Casing.
15. Distributors.
16. Left Distributor Elbow.
17. Right Distributor Elbow.
18. Dividing Rib.
19. Right Elevator Casing.
20. Oil Box.
21. Conveyor Reverse Lever.
22. Conveyor Oil Cups.
23. Rack Housing.
24. Rack.
25. Conveyor Pawl Casing.
26. Conveyor Screw Flexible Connection Sleeve.
27. Conveyor Screw Flexible Connection.
28. Conveyor Slide Support Roller.
29. Conveyor Slide Support.
30. Conveyor End Bearing and Gear Case.
31. Conveyor Screw Gear.
32. Conveyor Screw Driving Gear.



=AIR BRAKE QUESTIONS=

COMPRESSOR GOVERNOR


1. Q. When steam is first turned on, what must it pass through before
entering the compressor?

A. The compressor governor.

2. Q. What does Fig. 1 represent?

A. This shows a sectional view of the SF compressor governor in open
position.

3. Q. What is the duty of the compressor governor?

A. To automatically regulate the main reservoir pressure by controlling
the steam to the compressor.

4. Q. How are the regulating portions of the governor designated?

A. The one having two pipe connections and a light regulating spring is
known as the excess pressure head; the other, with a single pipe
connection and heavy regulating spring, as the maximum pressure head.

5. Q. When does the excess pressure head control the flow of steam to
the compressor?

A. When the automatic brake valve is in any one of its first three
positions; namely, release, running and holding positions.

6. Q. With the automatic brake valve in release, running or holding
position, what pressure is in chamber "f" above the diaphragm? In
chamber "d" below the diaphragm?

[Illustration: Fig. 1. The SF-4 Compressor Governor.
Connections: FVP, Feed Valve Pipe. ABV, Automatic Brake Valve.
MR, Main Reservoir. B, From Boiler. P, To Air Pump.]

A. Air, at feed valve pipe pressure, enters at the connection marked
"FVP" and flows to chamber "f" above the diaphragm; this pressure acts
in conjunction with the regulating spring 27 in creating the total
pressure on the diaphragm. Air at main reservoir pressure flows through
the automatic brake valve to the connection marked "ABV" to chamber "d"
under the diaphragm.

7. Q. At what pressure is the regulating spring in the excess pressure
head adjusted?

A. Usually twenty pounds.

8. Q. With the spring adjusted at twenty pounds, what will be the total
pressure on the upper side of the diaphragm?

A. Twenty pounds, plus the pressure in the feed valve pipe.

9. Q. With the feed valve adjusted at seventy pounds, and the regulating
spring at twenty pounds, what pressure will be had in the main reservoir
when the governor stops the compressor?

A. Ninety pounds.

10. Q. Explain the operation of the governor in controlling the
compressor when a main reservoir pressure of ninety pounds is reached.

A. When the main reservoir pressure in chamber "d" slightly exceeds the
pressure on top of the diaphragm it will move upward, carrying the pin
valve with it. The air in chamber "d" passes by the unseated pin valve
through port "b" into chamber "b" above the governor piston, forcing it
downward, seating the steam valve 5, thus shutting off the steam to the
compressor.

11. Q. How long will the governor remain in this position?

A. Until the main reservoir pressure falls below ninety pounds, when the
combined spring and air pressure in chamber "f" will force the diaphragm
28 down, seating the pin valve. This shuts off the supply of air from
chamber "d", and the air confined in chamber "b" will escape to the
atmosphere through the vent port "c". The pressure now being removed
from above the governor piston, the spring 9 aided by the steam pressure
under the valve 5, will force the piston upward, unseating the steam
valve 5, allowing steam to pass through the governor to the compressor.

12. Q. When the steam valve is seated, is steam entirely shut off from
the compressor?

A. No; there is a small port drilled through the valve; its purpose is
to maintain a circulation in the steam pipe and keep the compressor
working slowly; thereby preventing condensation when the steam valve is
closed.

13. Q. With the automatic brake valve in release, running, or holding
position, does the maximum pressure head operate?

A. No; as during this time the main reservoir pressure is not
sufficiently high to actuate its diaphragm.

14. Q. Where does the air come from that operates the maximum pressure
head?

A. From the main reservoir direct. (See Fig. 1.)

15. Q. When does the maximum pressure head control the compressor?

A. When the automatic brake valve is in either lap, service or emergency
position, also when the main reservoir cut-out cock is closed.

16. Q. How is the pressure created on top of the diaphragm in the
maximum pressure head?

A. By the regulating spring 19.

17. Q. What is the adjustment of this spring?

A. Spring 19 is adjusted to the maximum pressure desired in the main
reservoir usually 130 pounds.

18. Q. Explain the operation of the governor when the main reservoir
pressure exceeds the tension of the regulating spring 19.

A. When the pressure in chamber "a" exceeds the tension of the
regulating spring 19, the diaphragm 20 is forced upward, unseating the
pin valve, allowing air to flow from chamber "a" to chamber "b" above
the governor piston, forcing it down, shutting off steam and stopping
the compressor.

19. Q. How long will the governor remain in this position?

A. Until the main reservoir pressure in chamber "a" under the diaphragm
becomes slightly less than the adjustment of the regulating spring 19,
when the diaphragm 20 will move down, seating the pin valve, shutting
off the flow of air from chamber "a" to chamber "b". The air entrapped
above the governor piston will escape to the atmosphere through the
relief port "c"; this will allow the governor piston to raise, unseating
the steam valve 5, again allowing steam to pass through the governor to
the compressor.

20. Q. Is the maximum pressure head cut out in any position of the
automatic brake valve?

A. No; as the air that operates this head comes direct from the main
reservoir, therefore is not controlled by the brake valve.

21. Q. Is the excess pressure head cut out in any position of the brake
valve?

A. Yes; as the air that operates this head comes through the automatic
brake valve, and when the handle is moved beyond holding position, the
port in the rotary valve seat, through which the air flows to chamber
"d" is closed, thereby cutting out this head, leaving the compressor
under the control of the maximum pressure head.

22. Q. What is the object of the duplex or double head governor?

A. By use of the duplex governor the main reservoir pressure may be
controlled at two different predetermined pressures; as when running
along the excess or low pressure head controls the compressor, at the
low pressure--usually ninety pounds--this being sufficient to keep the
brakes released and fully charged; whereas, in lap position, as
following a brake application, the maximum or high pressure head
controls the compressor at the maximum pressure used--generally 130
pounds--this for a prompt release and quick recharge of the brakes. From
this it will be seen that the compressor has to work against the high
pressure only during the time the brake is applied.

23. Q. In what position should the automatic brake valve handle be
placed when adjusting the excess pressure head? The maximum pressure
head?

A. Running position for the excess pressure head; lap position for the
maximum pressure head.

24. Q. If, with the automatic brake valve handle in running position,
the brake pipe and main reservoir do not stand twenty pounds apart,
where would you look for the trouble?

A. Would first learn if the maximum pressure head was properly adjusted,
and if it were, would then look for the trouble in the adjustment of the
regulating spring in the excess pressure head.

25. Q. What should be done?

A. The regulating spring should be properly adjusted.

26. Q. How should the adjustment of the regulating spring in either
pressure head be made?

A. By removing the cap nut 25 or 17 and screwing the regulating nut 26
or 18 up or down as may be required.



DEFECTS OF THE GOVERNOR


27. Q. What would be the effect if one or both of the pin valves leaked?

A. Would cause a delay in opening of the steam valve after the pin valve
had seated; and if air leaks by faster than it can escape through the
relief port "c", pressure will accumulate in chamber "b" and force the
governor piston downward, so as to partially or wholly close the steam
valve 5.

28. Q. How can you tell if the pin valves leak?

A. Leakage past the pin valve in the maximum pressure head will cause a
constant blow at the relief port in all positions of the brake valve;
leakage past the pin valve in the excess pressure head will cause a blow
in the first three positions of the brake valve only.

29. Q. What would be the effect if the relief port "c" stopped up?

A. The compressor will not start promptly after the pin valve seats.

30. Q. What would be the effect if the drain port "W" were stopped up?

A. Steam leaking into the chamber under the governor piston will form a
pressure and prevent the piston being forced downward to close the steam
valve; the compressor will therefore continue to work until the main
reservoir pressure is about equal to boiler pressure.

31. Q. If the pipe leading from the feed valve pipe to the excess
pressure head of the governor breaks, what effect will it have on the
compressor?

A. The compressor will stop when the main reservoir pressure reaches
about forty-five pounds.

32. Q. If the pipe breaks, what should be done?

A. Plug the end toward the feed valve and put a blind gasket in the pipe
leading from the automatic brake valve to the governor, at the
connection marked ABV.

33. Q. If the pipe leading from the automatic brake valve to the
governor breaks, what should be done?

A. Plug the pipe toward the brake valve; the compressor will now be
controlled by the maximum pressure head.

34. Q. If the pipe leading from the main reservoir to the maximum head
of the governor breaks, what should be done?

A. Plug the main reservoir end of the pipe. The excess pressure head
will now control the compressor in the first three positions of the
automatic brake valve handle, but will have no control after the handle
is moved as far as lap position.



=PARASITE GOVERNOR=


35. Q. What is the purpose of the parasite governor, and where is this
governor located?

A. This governor is located in the pipe connection between the main
reservoir and parasite reservoir, and its purpose is to control the flow
of air from the main to the parasite reservoir.

36. Q. What is the purpose of the parasite reservoir?

A. It is here that air is stored for use in all air operated devices on
the locomotive, except the brake.

37. Q. Explain the operation of the parasite governor.

A. The operation of this governor is much the same as the compressor
governor, and differs only in that the supply valve is open when it is
in its lower position.

38. Q. At what pressure is the regulating spring adjusted?

A. About fifteen pounds.

39. Q. What pressure is required in the main reservoir before air is
admitted to the parasite reservoir?

A. At least fifteen pounds above that in the brake pipe.

40. Q. What pressure is obtained in the parasite reservoir?

A. The same as that in the main reservoir, when the main reservoir
pressure is fifteen pounds greater than that in the brake pipe.

41. Q. What will prevent the charging of the parasite reservoir, and
what should be done?

A. This may be caused by the feed valve being improperly adjusted,
sticking in open position or leakage of main reservoir air past the
valve to the feed valve pipe and governor top.



=WESTINGHOUSE 9-1/2 OR 11-INCH COMPRESSOR=


42. Q. What is the duty of the air compressor?

A. To furnish the compressed air used in the operation of the brakes,
and all other air operated appliances on both locomotive and cars.

43. Q. Explain the operation of the steam end of the compressor.

A. When steam is turned on at the boiler it flows through the steam pipe
and governor, entering the compressor at the steam enlet, then through
the steam passage "a" to the reversing valve chamber "C" also to the
main valve chamber "A" between the differential pistons 77 and 79. The
area of the piston at the right being greater than the one at the left,
the main valve is moved to the right, (See Fig. 2) admitting steam to
port "b" which leads to the lower end of the steam cylinder; steam is
now free to flow under the main piston, forcing it upward. When the
piston has almost completed its upward stroke, the reversing plate 69 on
top of the piston 65 engages a shoulder on the reversing rod 71, moving
the rod and reversing valve 72 upward (See Fig. 3). The upward movement
of the reversing valve closes the ports "f" and "h" and opens port "g";
thus permitting steam to enter the chamber at the right of the large
piston 77, balancing the pressure on this piston, and the pressure
acting on the right side of the small piston 79--the chamber at the left
being open to the exhaust--will force the main valve to the left.

[Illustration: Diagrammatic View, Up Stroke Fig. 2.]

When the main valve moves to the left, steam is admitted through port
"c" to the upper end of the cylinder on top of the piston 65, forcing it
downward. At the same time the lower end of the cylinder is connected
through exhaust cavity "b" of the main valve to the exhaust port "d",
allowing the steam below the piston to escape to the atmosphere.

44. Q. When the piston has about completed its downward stroke, what
takes place?

A. The reversing plate 69 engages the button "k" on the end of the
reversing rod 71 pulling the rod and the reversing valve down. This
movement of the reversing valve closes port "g" and the cavity in the
face of the valve connects ports "f" and "h", which allows the steam in
chamber "D" at the right of the large differential piston to escape to
the exhaust, thus allowing the main valve to move to the right,
exhausting the steam from the top end of the cylinder, and at the same
time admitting steam to the lower end, causing an upward stroke of the
piston.

45. Q. Explain the operation of the air end of the compressor.

A. The movement of the steam piston 65 is imparted to the air piston 66
by means of the piston rod. When the air piston moves up, a partial
vacuum is formed below it, and air from the atmosphere will enter
through passage "F" thence through passage "n" to the under side of
receiving valve 86b (see Fig. 2), lifting this valve from its seat, and
will fill the cylinder with air at about atmosphere pressure.

[Illustration: Diagrammatic View, Down Stroke Fig. 3.]

In the meantime the air above the piston, being compressed, will hold
the upper receiving valve 86a to its seat, and when the pressure is
slightly greater than that in the main reservoir, this pressure acting
under the upper discharge valve 86c, will lift this valve from its seat
and now the air will be free to flow through passage "G" to the main
reservoir connection. On the down stroke the action is similar, air is
taken in through the upper receiving valve 86a, while the air below the
piston is being compressed and forced past the lower discharge valve
86d, to the main reservoir. (See Fig. 3.)

46. Q. What lift should the air valves have?

A. All valves should have a lift of three thirty-second of an inch.

47. Q. At what speed should the compressor be run to obtain the best
results?

A. At 100 to 120 single strokes per minute.

48. Q. What kind of oil should be used in the air end of the compressor
and on the swab?

A. Valve oil.

49. Q. How often should the air end of the compressor be oiled?

A. No fixed rule can be given as so much depends on the condition of the
compressor, as well as the amount of work required; but in any case it
should be used sparingly.



CROSS-COMPOUND COMPRESSOR


50. Q. What do Figures 4 and 5 represent?

A. These are diagramatic views of a cross-compound compressor.

51. Q. Why is this called a cross-compound compressor?

[Illustration: Diagram of 8-1/2" Cross Compound Compressor. The
High Pressure Steam (Low Pressure Air) Piston on Its Upward Stroke
Fig. 4.]

A. Because both steam and air are compounded, that is, the steam is used
the second time before it is exhausted to the atmosphere, while the air
is compressed the second time before it is delivered to the main
reservoir.

52. Q. How many cylinders have the cross-compound compressor?

A. Four; two steam cylinders and two air cylinders.

53. Q. What is the diameter of the different cylinders?

A. The high pressure steam cylinder is 8-1/2 inches; the low pressure
steam cylinder 14-1/2 inches; the low pressure air cylinder 14-1/2
inches; high pressure air cylinder 9 inches.

54. Q. Explain the valve gear of this compressor.

A. The valve gear is the same as that of the 9-1/2 or 11 inch
compressor, only that a piston valve is used to distribute the steam
instead of a slide valve.

55. Q. Where does the steam come from that is used in the high pressure
steam cylinder?

A. Direct from the boiler.

56. Q. Where does the steam come from that is used in the low pressure
steam cylinder?

A. The steam after doing work in the high pressure steam cylinder is
exhausted into the low pressure steam cylinder, where it becomes the
working pressure of this cylinder.

57. Q. Explain the operation of this compressor.

A. When steam is first turned on, it enters the compressor at the steam
inlet (see Fig. 4) and flows through passage "a" into the reversing
valve chamber "C" and on to chambers "b" and "y" against the inner
faces of the differential pistons, causing the main valve to move to the
right. In this position of the main valve, port "g" is open to chamber
"b", thus admitting live steam to the lower end of the high pressure
steam cylinder, causing an upward movement of the piston 7. When the
piston 7 has nearly completed its up stroke, the reversing plate 18,
which is attached to the top of this piston, comes in contact with a
shoulder on the reversing rod 21, forcing it upward, carrying with it
the reversing valve 22, the movement of which closes port "m", at the
same time opens port "n", filling chamber "D" with live steam from
chamber "C" and passage "a". This balances the pressure on the two sides
of the large piston of the differential pistons, and the pressure acting
against the inner side of the small piston causes the main valve to move
to the left (see Fig. 5). The main valve moving to the left closes port
"g" to the live steam and at the same time connects this port with port
"f" leading to the lower end of the low pressure steam cylinder, causing
an up stroke of the low pressure steam piston 8. In the meantime port
"c", which leads to the upper end of the high pressure steam cylinder,
is open to chamber "y", allowing live steam to flow down on top of the
high pressure steam piston 7, forcing it downward. As the high pressure
steam piston about completes its downward stroke, the reversing plate 18
engages the button on the lower end of the reversing rod 21, pulling the
rod and reversing valve 22 down, closing port "n" and at the same time
connecting port "m" and "l" through the exhaust cavity "q", thus
allowing the steam in chamber "D" to escape to the exhaust. The pressure
being removed from the outer face of the large differential piston, the
main valve will again move to the right, opening port "g", admitting
live steam beneath the piston 7, and at the same time connecting the
upper end of the high pressure steam cylinder through port "c", chamber
"h" and port "d" to the upper end of the low pressure steam cylinder,
causing a downward movement of the low pressure steam piston; the steam
below this piston will now be free to escape to the exhaust through port
"f", chamber "i" and port "e". Thus it will be seen that the steam used
in the high pressure steam cylinder is live steam from the boiler, while
the steam used in the low pressure steam cylinder is the exhaust steam
from the high pressure steam cylinder.

58. Q. Explain the operation of the air end of the compressor.

A. As the low pressure air piston 9 moves up, a partial vacuum is
created beneath it and air from the atmosphere enters the air inlet and
passage "r" past the lower receiving valve 38 and fills the lower end of
the cylinder with air at about atmospheric pressure (see Fig. 4). In the
meantime the air above the piston being compressed will hold the upper
receiving valve 37 to its seat, thus preventing a back-flow of air to
the atmosphere; at the same time the upper intermediate discharge valves
39 are forced from their seats, allowing the air from the low pressure
air cylinder to flow through passage "u" to the high pressure air
cylinder, the piston of which is now moving downward. The air beneath
the high pressure air piston 10 being compressed will hold the lower
intermediate discharge valves 40 to their seats, thus preventing the air
in the high pressure air cylinder flowing back to the low pressure air
cylinder. When the pressure in the high pressure air cylinder becomes
slightly greater than the main reservoir pressure, the final discharge
valve 42 will be forced from its seat and the air beneath the piston
allowed to flow to the main reservoir through passage "w". On the
opposite strokes of these pistons air is compressed in a similar manner,
but the opposite air valves are used.

[Illustration: Diagram of 8-1/2" Cross-Compound Compressor. The
High Pressure Steam (Low Pressure Air) Piston on Its Downward Stroke
Fig. 5.]

59. Q. How many valves are there in the air end of the compressor?

A. Ten; two upper and two lower receiving valves; two upper and two
lower intermediate discharge valves; one upper and one lower final
discharge valves.

60. Q. Are the air valves all the same size?

A. No; the receiving and final discharge valves are the same size and of
the size used in the 11-inch compressor, while the intermediate valves
are the same as used in the 9-1/2-inch compressor. The receiving and
final discharge valves are two inches in diameter, while the
intermediate valves are one and one-half inches.

61. Q. What lift is given the different air valves?

A. All valves have 3/32-inch lift.


DEFECTS OF THE COMPRESSOR

62. Q. What are some of the common causes for the compressor stopping?

A. Lack of lubrication; bent, worn or broken reversing rod; loose or
worn reversing plate; nuts on air end of piston rod coming off;
defective compressor governor; and, in addition with the cross-compound
compressor, final discharge valve broken or stuck open, or packing rings
in main valve pistons breaking and catching in the steam ports.

63. Q. What will cause the piston to make an uneven stroke?

A. This may be caused by a broken or stuck open air valve, or air valves
not having proper lift. Where the piston short strokes, it is generally
caused by over-lubrication of the steam end.

64. Q. What are some of the common causes for the compressor running
hot?

A. The overheating of the compressor may be due to any one of the
following causes: Running at high speed; working against high pressure;
packing rings in air piston badly worn; air cylinder worn; defective air
valves; air passages or air discharge pipe partially stopped up; leaky
piston rod packing; lack of lubrication.

65. Q. What will cause the compressor to run slow?

A. This may be caused by leaky air piston packing rings; final discharge
valves leaking, or air passages partially stopped up. A defective
governor may also cause the compressor to run slow.

66. Q. What will cause the compressor to run very fast and heat, and not
compress any air?

A. This may be caused by the strainer becoming clogged with ice or dirt,
preventing air entering the cylinder.

67. Q. If, when steam is first turned on, the piston makes a stroke up
and stops, where would you look for the trouble?

A. The shoulder on the reversing rod may be worn; the opening in the
reversing plate too large to engage the shoulder on the reversing rod;
loose reversing plate studs preventing the piston traveling far enough
to reverse the compressor, or the main valve stuck in its position at
the right.

68. Q. If the piston makes a stroke up and a stroke down and stops,
where is the trouble?

A. This may be caused by a loose reversing plate, or the button on the
lower end of the reversing rod worn or broken off, or the nuts off the
piston rod in the air end, or the main valve stuck in its position at
the left.

69. Q. What will cause the piston to make a quick up stroke?

A. This may be caused by a broken or stuck open upper receiving or lower
discharge valve.

70. Q. What will cause the piston to make a quick down stroke?

A. Lower receiving or upper discharge valve broken or stuck open.

71. Q. If a receiving valve breaks or sticks open, how may it be
located?

A. The air will flow back to the atmosphere as the piston moves toward
the defective valve and may be detected by holding the hand over the
strainer.

72. Q. If a receiving valve in a cross-compound compressor breaks, what
may be done?

A. Remove the broken valve, blocking the opening made by its removal,
and as there are two upper and two lower receiving valves the compressor
will now take air through the other valve.

73. Q. If an intermediate discharge valve breaks or sticks open, how may
it be located?

A. No air will be taken in to that end of the compressor as the piston
moves from the defective valve, and may be located by holding the hand
over the strainer.

74. Q. If an intermediate discharge valve breaks, what may be done?

A. Remove the broken valve, blocking the opening made by its removal,
and as there are two upper and two lower intermediate discharge valves
the air will now pass from the low pressure cylinder to the high
pressure cylinder through the other valve.

75. Q. If a final discharge valve breaks, what effect will it have on
the compressor?

A. Will cause the compressor to stop when the main reservoir pressure is
in excess of forty pounds.

76. Q. How would you test for a defective final discharge valve?

A. To test for this defect, bleed the main reservoir pressure below
forty pounds, and if the compressor starts it indicates a defective
discharge valve.

77. Q. If a final discharge valve breaks, what may be done?

A. As the receiving valves and final discharge valves are the same size,
the defective valve may be replaced by one of the receiving valves,
blocking the opening made by the removal of the receiving valve.

78. Q. Where piston rod packing is blowing bad, what may be done to stop
it?

A. This generally indicates lack of lubrication, and by cleaning and
oiling the swab the trouble may be overcome. However, there are times
when leakage by the packing is so great that the oil is blown off the
swab as fast as it is applied, therefore is of no value in lubricating
the parts. Where this condition exists, a little hard grease wrapped up
in an old flag and tied around the piston rod will ensure its being
lubricated.

79. Q. If the compressor stops, how can you tell if the governor is
responsible for the trouble?

A. By opening the drain cock in the steam passage between the governor
and the compressor; if steam flows freely, the trouble is in the
compressor; if not, it is in the governor.

80. Q. How may a compressor often be started when it stops?

A. By closing the steam throttle for a few seconds, then opening it
quickly; if this does not start it, try tapping the main valve chamber.
This will usually overcome the trouble where the compressor stops on
account of lack of lubrication.

81. Q. What will cause a compressor to short-stroke or dance?

A. Too much oil in the steam end; bent reversing rod; or low steam
pressure, as when the governor has almost shut off the steam.


ENGINEER'S BRAKE VALVE

82. Q. Name the different positions of the G-6 and H-6 brake valves.

A. Release, running, lap, service, and emergency position, with the G-6;
release, running, holding, lap, service, and emergency positions, with
the H-6.

83. Q. What is the purpose of release position?

A. To provide a large and direct opening from the main reservoir to the
brake pipe, for the free flow of air, when charging and recharging the
brakes.

84. Q. What pressure will be had in the brake pipe if the brake valve be
left in release position?

A. Main reservoir pressure.

85. Q. Can the locomotive brake be released by the automatic brake valve
in release position, when using the H-6 valve?

A. No; as the port in the automatic brake valve to which the
distributing valve release pipe is attached is blanked in this position
of the valve.

86. Q. What is the purpose of running position, and when should it be
used?

A. This is the proper position for the brake valve when the brakes are
charged and not in use, also when it is desired to release the
locomotive brake with this valve. In this position the brake pipe
pressure is maintained at a predetermined amount by the feed valve, as
all air that now enters the brake pipe must pass through the feed valve.

87. Q. What is the purpose of holding position?

A. To hold the locomotive brake applied while recharging the brakes. The
charging of the brake pipe and equalizing reservoir is the same in
holding as in running position.

88. Q. What is the purpose of lap position?

A. To hold both the locomotive and train brakes applied after an
automatic application.

89. Q. What is the purpose of service position?

A. This position of the brake valve enables the engineer to make a
gradual reduction of brake pipe pressure, thus causing a service
application of the brakes.

90. Q. What is the purpose of emergency position?

A. In this position of the brake valve, the brake pipe is connected
directly with the atmosphere through the large ports in the valve,
causing a sudden reduction of brake pipe pressure, this in turn causing
the distributing valve on the engine and all operating triple valves on
cars in the train to move to emergency position, thus insuring a quick
and full application of the brake.

91. Q. How should the brake valve be handled when making an emergency
application of the brake?

A. The valve should be placed in full emergency position and left there
until the train stops, even though the danger may have disappeared.


DEFECTS OF THE BRAKE VALVE

92. Q. What will cause a constant blow at the brake pipe exhaust port,
and what may be done to overcome it?

A. This indicates that the brake pipe exhaust valve is being held off
its seat, due no doubt to dirt; tapping the side of the valve will
sometimes stop the blow; if not, close the brake pipe cut-out cock and
make a heavy service reduction; next, place the brake valve handle in
release position. This will cause a strong blow at the exhaust port,
which will invariably remove the trouble.

93. Q. If the pipe connecting the brake valve with the equalizing
reservoir breaks, can both locomotive and train brakes be operated with
the automatic brake valve?

A. Yes; by placing a blind gasket in the pipe connection at the brake
valve and plugging the brake pipe exhaust port. To apply the brake, move
the handle carefully toward emergency position, making a gradual
reduction of brake pipe pressure through the direct exhaust ports of
the brake valve; when the desired reduction is made, the handle should
be moved gradually back to lap position.

94. Q. What would be the effect if the handle were moved to lap quickly?

A. Would cause the release of the brakes on the head end of the train.

95. Q. What will cause air to blow at the brake pipe exhaust port when
the handle is moved to lap position?

A. This is caused by a leak from the equalizing reservoir or its
connections, which reduces the pressure in chamber "D" above the
equalizing piston, allowing brake pipe pressure under the piston to
force it up, unseating the brake pipe exhaust valve, permitting brake
pipe air to flow to the atmosphere.

96. Q. What is the purpose of the equalizing reservoir?

A. The purpose of the equalizing reservoir is to furnish a larger volume
of air above the equalizing piston than is found in chamber "D", thus to
enable the engineer to make a graduated reduction of the pressure above
the equalizing piston.

97. Q. What defect will cause the brake pipe and main reservoir pressure
to equalize when the handle is in running position?

A. This may be caused by leakage past the rotary valve, defective body
gasket, or leakage by the feed valve or its case gasket. To determine
which part is at fault, close the cut-out cock under the brake valve
and move the handle to service position, exhausting all air from chamber
"D" and the brake pipe; return the handle to lap position. Leakage of
air past the rotary valve is generally into the brake pipe port which
allows the air to come in under the equalizing piston, thus forcing it
upward, unseating the brake pipe exhaust valve, allowing this air to
escape to the atmosphere at the brake pipe exhaust port. Leakage past
the body gasket allows air to enter chamber "D", above the equalizing
piston, holding it in its lower position, keeping the brake pipe exhaust
port closed, thereby preventing the escape of this air to the
atmosphere. Since the capacity of the equalizing reservoir and chamber
"D" is small, such a leak will cause the black hand to quickly move up
to the position of the red hand. To determine if the leakage be in the
feed valve or its gasket, recharge the brake pipe to some pressure below
the adjustment of the feed valve, then place the handle in lap position.
If the black hand on the air gauge remains stationary, it is fair to
assume that the trouble is in the feed valve or its gasket, as in this
position of the brake valve the feed valve is cut out.

98. Q. With the engine alone, the brake pipe pressure will equalize with
that in the main reservoir, while when coupled to a train the pressure
will remain at that for which the feed valve is adjusted; where is the
trouble?

A. This is caused by light leakage of main reservoir air into the brake
pipe, and may come past the rotary valve, body gasket, or feed valve,
and with the lone engine is sufficient to raise the brake pipe pressure
to that in the main reservoir; while, when coupled to a train, the brake
pipe leakage of which is greater than this amount, this leakage will not
be noticed.



THE FEED VALVE AND ITS DEFECTS


99. Q. What do Figures 6 and 7 represent?

A. These are diagrams of the B-6 feed valve in both open and closed
positions.

100. Q. Name the different parts of the feed valve.

A. The valve consists of the following parts: 2, valve body; 3, pipe
bracket; 5, cap nut; 6, piston spring; 7, piston spring tip; 8, supply
valve piston; 9, supply valve; 10, supply valve spring; 11, regulating
valve cap nut; 12, regulating valve; 13, regulating valve spring; 14,
diaphragm; 15, diaphragm ring; 16, diaphragm spindle; 17, regulating
spring; 18, spring box; 19 and 20, stop rings; 21, clamping screw; 22,
hand wheel.

101. Q. Explain the operation of the feed valve.

A. The feed valve consists of two portions, the supply and regulating
portions. The supply portion consists of a slide valve 9 and a piston 8
(see Fig. 6). The supply valve 9 opens and closes communication between
the main reservoir and the feed valve pipe and is moved by the piston 8
which is operated by main reservoir air entering through passage "a" on
one side or by the pressure of the spring 6 on the other side. The
regulating portion consists of a brass diaphragm 14, on one side of
which is the diaphragm spindle 16, held against the diaphragm by the
regulating spring 17, and on the other side a regulating valve 12, held
against the diaphragm or its seat, as the case may be, by the spring 13.
Chamber "L" at the left of the diaphragm is open to the feed valve pipe
through the passage "e" and "d". The feed valve is adjusted by turning
the hand wheel 22 in or out, thus increasing or decreasing the pressure
exerted by the spring on the diaphragm. The same results are obtained
in turning the hand wheel 22 as when turning the adjusting screw in the
older types of feed valves.

[Illustration: Fig. 6. Diagram of B-6 Feed Valve, Closed.
Connections: MR, Main Reservoir Pipe; FVP, Feed Valve Pipe.]

Air from the main reservoir flowing through passage "a" into chamber "B"
will force the piston 8 to the left against the tension of the spring 6;
the piston in moving will take with it the supply valve 9, opening the
supply port in the valve to port "c" in its seat as shown in Fig. 7.
Main reservoir air will now be free to flow through passage "a", chamber
"B", port "c" and passage "d" to the feed valve pipe. Air coming through
port "c" also flows through passage "e" to chamber "L" at the left of
the diaphragm 14, and this pressure tends toward forcing the diaphragm
to the right; but the diaphragm being supported by the regulating spring
17, will remain in its position at the left, holding the regulating
valve 12 off its seat, until the pressure in chamber "L" exceeds the
tension of the regulating spring 17. Air, therefore, continues to flow
from the main reservoir through a, B, c, d and e to the feed valve pipe
and chamber "L", increasing the pressure, until the pressure on the
diaphragm 14 overcomes the tension of the regulating spring 17, when the
diaphragm will move to the right, allowing the spring 13 to force the
regulating valve 12 to its seat, closing port "K". Chambers "G" and "H"
are then no longer open to chamber "L" and the feed valve pipe, and
these chambers being small, the pressure raises quickly to main
reservoir pressure due to the leakage of air past the supply piston 8,
which forms but a loose fit in its bushing. When the pressure in chamber
"G" becomes nearly equal to that in chamber "B", the piston spring "6"
forces the piston 8 and its slide valve 9 to closed position, which
prevents further flow of air from the main reservoir to the feed valve
pipe (see Fig. 6). The feed valve will remain in closed position until
the pressure in chamber "L" is slightly reduced so that the pressure on
the diaphragm 14 is no longer able to withstand the pressure of the
regulating spring 17, which then forces the diaphragm to the left,
lifting the regulating valve 12 from its seat and again opening port "K"
to chamber "L", thus dropping the pressure at the left of piston 8 below
that of the main reservoir acting on the opposite side of the piston.

[Illustration: Fig. 7. Diagram of B-6 Feed Valve, Open.]

Main reservoir pressure then forces the supply piston and valve over
into open position, as shown in Fig. 7, and allows a further flow of air
through port "c" to the feed valve pipe to again raise its pressure to
the adjustment of the feed valve, when the valve will again close.

102. Q. What is the duty of the feed valve?

A. To control and maintain a constant pressure in the brake pipe when
the brake valve is in running or holding position.

103. Q. What defect in the feed valve will cause the brake pipe pressure
to equalize with that in the main reservoir?

A. This may be caused by a defective feed valve case gasket, permitting
main reservoir air to leak into the feed valve pipe, or leakage past the
supply valve, or the regulating valve held from its seat, or the supply
valve piston too tight a fit in its cylinder.

104. Q. If the brake pipe charges too slowly when nearing the maximum
pressure, where is the trouble?

A. This may be caused by a loose-fitting supply valve piston 8, or the
port past the regulating valve 12 partly stopped up.

105. Q. How should the feed valve be tested?

A. With the brakes released, and charged to the adjustment of the feed
valve, create a brake pipe leak of from seven to ten pounds and note the
black hand on the brake pipe gauge. The fluctuation of this hand will
indicate the opening and closing of the feed valve, which should not
permit a variation of over two pounds in brake pipe pressure; if it
does, it indicates a dirty condition of the valve, and should be
cleaned.

106. Q. If the main reservoir pipe connection to the feed valve breaks,
what should be done?

A. This will cause a loss of main reservoir air, and both ends of the
pipe must be plugged. As no air now comes to the feed valve to charge
the brake pipe in running or holding position of the brake valve, the
handle must be carried in release position.

107. Q. What must be done if the pipe between the feed valve and
automatic brake valve breaks?

A. Slack off on the regulating nut of the feed valve until all tension
is removed from the regulating spring and plug the pipe toward the brake
valve. To charge the brake pipe, the brake valve handle must be carried
in release position.

108. Q. If the feed valve becomes defective so that it will not control
brake pipe pressure, what may be done?

A. As the reducing valve used for the independent brake, and the feed
valve are practically the same, they may be changed one for the other,
the reducing valve taking the place of the feed valve.


INDEPENDENT BRAKE VALVE

109. Q. Name the different positions of the independent brake valve used
with the E-T equipment.

A. Release, running, lap, slow-application position, quick-application
position.

110. Q. What is the purpose of release position?

A. To release the locomotive brake when the automatic brake valve is in
other than running position.

111. Q. What is the purpose of running position?

A. This is the proper position for the brake valve when not in use, and
to release the locomotive brake when the automatic brake valve is in
running position.

112. Q. What is the purpose of lap position?

A. To hold the locomotive brake applied after an independent
application.

113. Q. What is the purpose of slow-application position?

A. This position may be used when it is desired to make a light or
gradual application of the brake, as in stretching or bunching the slack
of a train.

114. Q. What is the purpose of quick-application position?

A. To apply the locomotive brake quickly, as in short switching.

115. Q. What brake cylinder pressure is usually developed with this
brake?

A. About forty-five pounds.



DEAD ENGINE FEATURE


116. Q. What is the dead engine device?

A. The dead engine device is a pipe connection between the main
reservoir and the brake pipe. In this pipe is found a combined strainer
and check valve with a choke fitting and cut-out cock, which when open
forms a connection between the brake pipe and the main reservoir.

117. Q. What is the purpose of this device?

A. To provide a means of charging the main reservoir of an engine whose
compressor is inoperative.

118. Q. What is the object of charging a main reservoir of an engine
with a disabled compressor?

A. As the air used in the locomotive brake cylinders comes from the main
reservoir, for the brakes to be operated on this engine it is necessary
that its main reservoir be charged.

119. Q. With a 70-pound brake pipe pressure, what pressure should be had
in the main reservoir when using this device?

A. About fifty pounds.

120. Q. When the dead engine feature is being used, in what position
should the automatic and independent brake valves be carried?

A. Running position.

121. Q. What should be the position of the brake pipe cut-out cock below
the brake valve?

A. It should be closed.



DISTRIBUTING VALVE


122. Q. What is the duty of the distributing valve?

A. To admit air from the main reservoir to the locomotive brake
cylinders when applying the brake, to automatically maintain the brake
cylinder pressure against leakage, to develop the proper brake cylinder
pressure regardless of piston travel and to exhaust the air from the
brake cylinders when releasing the brake.

123. Q. To what is the distributing valve attached?

A. To the distributing valve reservoir.

124. Q. How many chambers has the distributing valve reservoir?

A. Two; pressure chamber and application chamber.

[Illustration: Fig. 8. Release, Automatic or Independent.
Connections: MR, Main Reservoir Pipe; IV, Distributing
Valve Release Pipe; II, Application Cylinder Pipe; CYLS,
Brake Cylinder Pipe; BP, Brake Pipe.]

125. Q. Name the different pipe connections to the distributing valve
reservoir.

A. Referring to Fig. 8, the connection marked "MR" is the main reservoir
supply pipe; "II", application cylinder pipe; "IV", distributing valve
release pipe; "BP", brake pipe; "CYLS", brake cylinder pipe.

126. Q. To what do these different pipes connect?

A. The main reservoir supply pipe connects the distributing valve with
the main reservoir pipe. The application cylinder pipe connects the
application cylinder of the distributing valve with the independent and
automatic brake valves. The distributing valve release pipe connects the
application cylinder exhaust port in the distributing valve with the
independent brake valve, and through it, when in running position, to
the automatic brake valve. The brake cylinder pipe connects the
distributing valve with the different brake cylinders on the locomotive.
The brake pipe branch pipe connects the distributing valve with the
brake pipe.

127. Q. Explain the operation of the distributing valve when making an
automatic service application of the brake.

A. When the brakes are fully charged, the brake pipe and pressure
chamber pressures are equal, and when a gradual reduction of brake pipe
pressure is made it will be felt in chamber "p" at the right of the
equalizing piston 26, creating a difference in pressure on the two sides
of the piston, causing it to move to the right. The first movement of
the piston closes the feed groove "v", also moves the graduating valve
28, uncovering the service port "z" in the equalizing slide valve 31;
this movement of the piston also causes the shoulder on the end of its
stem to engage the equalizing slide valve, and the continued movement
of the piston moves the valve to service position, in which port "z"
connects with port "h" in the seat of the valve, as shown in Fig. 9. As
the equalizing slide valve chamber is at all times connected to the
pressure chamber, air can now flow from this chamber to both the
application cylinder and chamber through ports "z" and "h", cavity "n"
and port "w" until the pressure on the left or pressure chamber side of
the equalizing piston 26 becomes slightly less than that in the brake
pipe, when the piston and graduating valve will move to the left until
the shoulder on the piston stem strikes the slide valve; this movement
of the graduating valve closes the service port "z", thus closing the
communication between the pressure chamber and application chamber and
cylinder, also closing port "l" which leads to the safety valve. The
distributing valve is now said to be in service lap position. (See Fig.
10.)

128. Q. Upon what does the pressure in the application chamber and
cylinder depend when making a service application of the brake?

A. On the amount of brake pipe reduction; and as the relative volume of
the pressure chamber and application cylinder and chamber is practically
the same as that of an auxiliary reservoir and brake cylinder, it will
be understood that one pound from the pressure chamber will make two and
one-half pounds in the application chamber and cylinder; in other words,
with the pressure chamber charged to seventy pounds and no pressure in
the application chamber and cylinder, if they were connected and the
pressure allowed to equalize it would do so at about fifty pounds; that
is, twenty pounds from the pressure chamber will make fifty pounds in
the application chamber and cylinder.

[Illustration: Fig. 9. Automatic Service.]

129. Q. How is the application piston 10 affected by the air pressure in
the application cylinder "g"?

A. Pressure forming in this cylinder will force the piston to the right;
the piston in moving will carry with it the exhaust valve 16, closing
the exhaust ports "e" and "d", at the same time moving the application
valve 5, opening the supply port "b", allowing main reservoir air from
chamber "a" to flow through ports "b" and "C" to the connection marked
"CYLS", and on to the different brake cylinders of the locomotive until
the pressure in the brake cylinders and at the right of the application
piston becomes slightly greater than that in chamber "g" when the
application piston and valve will move back to lap position as shown in
Figures 9 and 10.

130. Q. With the application valve in lap position, if there be brake
cylinder leakage, will the locomotive brake leak off?

A. No; any drop in brake cylinder pressure will be felt in chamber "b"
at the right of the application piston 10, causing a difference in
pressure on the two sides of the piston, thus allowing the pressure in
the application cylinder to move the application piston and valve to the
right, again opening the supply port "b" allowing a further flow of main
reservoir air from chamber "a" to the brake cylinders until the pressure
is again slightly greater than that in the application cylinder "g",
when the application piston and valve will move back to lap position.
Thus in this way air will be supplied to the brake cylinders of the
locomotive, holding the brake applied regardless of leakage.

131. Q. What effect will piston travel have on the pressure developed in
the brake cylinders?

A. None; as the pressure in the brake cylinders is entirely dependent on
the pressure in the application cylinder, which is not affected by
piston travel.

132. Q. Explain the movement of the parts in the distributing valve when
the automatic brake valve is moved to release position, after an
automatic application of the brake.

A. In release position of the brake valve, air from the main reservoir
flows direct to the brake pipe, causing a rise of pressure which is felt
in chamber "p" on the right or brake pipe side of the equalizing piston
26; this increase of pressure will cause the piston to move toward the
left, carrying the graduating valve 28 and slide valve 31 to release
position.

[Illustration: Fig. 10. Service Lap.]

This allows the air from the application chamber and cylinder to flow to
the distributing valve release pipe "IV" and on through the independent
brake valve to the automatic brake valve, where the port to which this
pipe leads is blanked by the automatic rotary valve, thus preventing the
air from leaving the application chamber and cylinder, holding the
locomotive brake applied while the train brakes are being released. The
movement of the parts, and the results obtained are the same where the
release is made in holding position.

133. Q. Explain the movement of the parts in the distributing valve when
the brake valve is moved to running position after having first been
moved to release or holding position, following a brake application.

A. In this position of the brake valve the port to which the
distributing valve release pipe is connected is open to the exhaust,
thus allowing the air to escape from the application chamber and
cylinder. The reduction of pressure in chamber "g", will allow the brake
cylinder pressure in chamber "b" to force the application piston and its
valves to release position, thus allowing the brake cylinder air to
escape to the atmosphere, through the exhaust ports "e" and "d". (See
Fig. 8.)

134. Q. Explain how an independent release of the locomotive brake is
obtained after an automatic application has been made.

A. If the brakes have been applied throughout the train, by means of the
automatic brake valve, and it is desired to release the locomotive
brakes without releasing the train brakes, the handle of the independent
brake valve is placed in release position. In this position of the
independent brake valve, the application cylinder in the distributing
valve is connected through the application cylinder pipe to the direct
exhaust port of the independent brake valve; thus exhausting the air
from the application cylinder, causing a release of the locomotive
brake. This independent release of the locomotive brake does not cause
the equalizing piston and its slide valve in the distributing valve to
change their position.

135. Q. Explain what takes place when an automatic emergency application
is made.

A. Any sudden reduction of brake pipe pressure is felt on the brake pipe
side of the equalizing piston 26 and will cause it and the slide valve
31 to move to the extreme right, compressing the graduating spring 60.
(See Fig. 11.) In this position pressure chamber air can flow to the
application cylinder only as the application chamber is now cut off.
This will cause a quick rise of pressure in the application cylinder,
forcing the application piston and its valves to full application
position, admitting main reservoir air to the brake cylinders and
applying the brake. In emergency position of the automatic brake valve
there is a small port in the rotary valve, called the blow-down timing
port, through which main reservoir air is free to flow to the
application cylinder "g" through the application cylinder pipe "II",
causing a rise of pressure equal to the adjustment of the safety valve.

136. Q. At what pressure is the safety valve adjusted?

A. At sixty-eight pounds.

137. Q. What is the purpose of the quick action cap, and where is it
located?

A. Its purpose is to assist the brake valve in venting brake pipe air
when an emergency application of the brake is made, and is located on
the brake pipe side of the distributing valve in place of the plain cap.
(See Figs. 8 and 11.)

138. Q. Explain the operation of the quick action cap.

[Illustration: Fig. 11. Emergency Position of No. 6 Distributing
Valve with Quick-Action Cap.]

A. In an emergency application, the equalizing piston 26 moves to the
extreme right, the knob on the piston strikes the graduating stem 59,
causing it to compress the graduating spring 46, and move the slide
valve 48 to the right, opening port "j".

[Illustration: Fig. 12. Independent Application.]

Brake pipe pressure in chamber "p" flows to chamber "X", pushes down
check valve 53, and passes to the brake cylinders through port "m" in
the cap and distributing valve body. When the brake cylinders and brake
pipe pressures equalize, check valve 53 is forced to its seat by spring
54, thus preventing air in the brake cylinders from flowing back into
the brake pipe. When a release of the brake occurs and piston 26 is
moved back to its normal position, spring 46 forces graduating stem 59
and slide valve 48 back to release position.

139. Q. Explain the operation of the distributing valve when making an
independent application of the brake.

A. When the independent brake valve handle is moved to application
position, air is admitted from the reducing valve pipe through the
application cylinder pipe to the application chamber and cylinder.
Pressure forming in the application cylinder will move the application
piston 10 to the right, carrying with it the exhaust valve 16 and the
application valve 5, closing the exhaust port and opening the supply
port, admitting main reservoir air from chamber "a" to the brake
cylinders (see Fig. 12) until the pressure in the brake cylinders and
chamber "b" slightly exceeds that in chamber "g", when the application
piston 10 and valve 5 will move back to lap position. By moving the
brake valve handle to either release or running position, the air is
exhausted from the application cylinder and chamber, thus reducing the
pressure in chamber "g", allowing the pressure in chamber "b" to force
the piston to the left, carrying with it the exhaust valve 16, opening
the exhaust ports "e" and "d", allowing the air from the brake cylinders
to escape to the atmosphere, thus releasing the brake.



DISTRIBUTING VALVE DEFECTS


140. Q. If the locomotive brake released with the automatic brake valve
in lap position, where would you look for the trouble?

A. Would look for a leak in the application cylinder pipe or in the
application cylinder cap gasket.

141. Q. If the brake remained applied in lap position, but released in
release or holding position, where would you look for the trouble?

A. Would look for a leak in the distributing valve release pipe.

142. Q. If the distributing valve release pipe and application cylinder
pipe were crossed, what would be the effect?

A. A brake application made by the automatic brake valve cannot be
released by the independent brake valve.

143. Q. If the safety valve leaks, what will be the effect?

A. This may prevent the brake applying, and in an independent
application if the brake does apply, it will release when the brake
valve is returned to lap position.



BROKEN PIPES


144. Q. If the main reservoir supply pipe to the distributing valve
breaks, what should be done?

A. Plug the pipe toward the main reservoir. The locomotive brake is
lost, but if the distributing valve is equipped with a quick action cap,
when an emergency application is made, the air coming from the brake
pipe, through the quick action cap, will apply the locomotive brake.

145. Q. If the application cylinder pipe breaks, what effect will it
have on the locomotive brake?

A. The locomotive brake cannot be applied with either automatic or
independent brake valve. By plugging the pipe toward the distributing
valve the automatic brake will be restored.

146. Q. If the distributing valve release pipe breaks, what will be the
effect?

A. The holding feature of the brake will be lost; that is, the
locomotive brake will release when the automatic brake valve is moved to
either release or holding position, the same as with the old G-6
equipment.

147. Q. If the release pipe is broken and not plugged, can the
independent brake be applied?

A. Yes, by placing the brake valve handle in quick-application position
the brake will apply, but there will be a waste of air through the
broken pipe, and the brake will release when the brake valve is returned
to lap position.

148. Q. If the brake cylinder pipe breaks, can the locomotive brake be
applied?

A. This depends on where the pipe breaks; if between the cut-out cock
and any one of the brake cylinders, close the cut-out cock to that
cylinder, and the other cylinders may be used. But if the pipe breaks at
the distributing valve, the locomotive brake will be lost.

149. Q. If the brake pipe connection to the distributing valve breaks,
what should be done?

A. Plug the end from the brake pipe; the locomotive brake must now be
released by placing the independent valve in release position.

150. Q. If the brake pipe connection to the distributing valve breaks
and is plugged, can the locomotive brake be operated?

A. The independent brake may be applied and released in the usual
manner, but the automatic brake will be lost for service braking.



TYPE K TRIPLE VALVE


151. Q. On what is this type of triple valve designed to operate?

A. On freight equipment cars only.

152. Q. Explain the operation of the "K" triple valve.

[Illustration: Fig. 13. Full Release and Charging Position.]

A. When air is admitted to the brake pipe it is free to enter the triple
at "a" (see Fig. 13) and flow through the passage "e" to chamber "f",
thence through port "g" to chamber "h" in front of the triple valve
piston 4. Pressure forming in chamber "h" will force the piston to the
left until its packing ring uncovers the feed groove "i" in the bushing,
thus creating a communication between chamber "h" and the slide valve
chamber. Brake pipe air will now be free to flow past the piston to the
slide valve chamber and out at "R" to the auxiliary reservoir. Air will
continue to feed through the groove "i" until the auxiliary reservoir
and brake pipe pressures are equal, and it is then we say that the brake
is fully charged. Brake pipe air entering chamber "a" will lift the
check valve 15, and charge chamber "Y" to brake pipe pressure. When a
gradual reduction of brake pipe pressure is made, as in a service
application of the brakes, the pressure being reduced in chamber "h",
auxiliary reservoir pressure will move the piston 4 toward service
position. (See Fig. 14.) The first movement of the piston closes the
feed groove "i", thus closing communication between the auxiliary
reservoir and the brake pipe, preventing a back-flow of air from the
auxiliary to the brake pipe, and at the same time moving the graduating
valve 7, opening the service port "Z" in the slide valve. The continued
movement of the piston will move the slide valve until the service port
"Z" registers with the brake cylinder port "r" in the valve seat, thus
creating a communication between the auxiliary reservoir and the brake
cylinder. Air will now flow from the auxiliary to the brake cylinder
until the pressure on the auxiliary side of the piston 4 becomes
slightly less than in the brake pipe, when the piston and the graduating
valve 7 will move back just far enough to close the service port "Z",
thus closing communication between the auxiliary reservoir and the
brake cylinder. At the same time, the first movement of the graduating
valve connects the two ports "o" and "q" in the slide valve through the
cavity "v" in the graduating valve, and the movement of the slide valve
brings port "o" to register with port "y" in the slide valve seat, and
port "q" with port "t". This permits the air in chamber "Y" to flow
through port "y", "o", "v", "q", and "t", thence around the emergency
piston 8, which fits loosely in its cylinder, to chamber "X" and the
brake cylinder. When the pressure in chamber "Y" has reduced below the
brake pipe pressure remaining in chamber "a", the check valve 15 is
raised and allows brake pipe air to flow past the check valve and
through the ports above mentioned to the brake cylinder.

[Illustration: Fig. 14. Quick Service Position.]

The size of these ports are so proportioned that the flow of air from
the brake pipe to the top of the emergency piston 8, is not sufficient
to force the latter downward and thus cause an emergency application,
but at the same time takes enough air from the brake pipe to cause a
local reduction of brake pipe pressure at that point, thus assisting the
brake valve in increasing the rapidity with which the brake pipe
reduction travels through the train. The triple valve is now said to be
in "Quick Service" position. (See Fig. 14.)

153. Q. Will the triple valve move to quick service position whenever a
gradual reduction brake pipe reduction is made?

A. No; with short trains, the brake pipe volume being comparatively
small, will reduce more rapidly for a certain reduction at the brake
valve than with a long train. Therefore, with a short train, the brake
pipe pressure reducing more quickly, the triple piston and its valves
will move to "full service" position, as shown in Fig. 15. In this
position the quick service port "y" is closed, so that no air flows from
the brake pipe to the brake cylinder. Thus, when the brake pipe
reduction is sufficiently rapid, there is no need for this quick service
reduction, and the triple valve automatically cuts out this feature of
the valve when not required.

154. Q. How long will the auxiliary reservoir air continue to flow to
the brake cylinder?

A. Air will continue to flow to the brake cylinder until the pressure on
the auxiliary side of the triple piston becomes slightly less than that
on the brake pipe side, when the piston 4 and the graduating valve 7
will move to the left until the shoulder on the piston stem strikes the
slide valve. (See Fig. 16.) This movement has caused the graduating
valve to close the service port "Z", thus cutting off any further flow
of air from the auxiliary to the brake cylinder and also port "o", thus
preventing any further flow of air from the brake pipe to the brake
cylinder. The triple valve is now said to be in lap position.

155. Q. How is the triple valve affected by a further reduction of brake
pipe pressure?

[Illustration: Fig. 15. Full Service Position.]

A. A further reduction of brake pipe pressure will cause the triple
piston 4 and the graduating valve 7 to again move to the right, opening
ports "Z" and "o", allowing a further flow of brake pipe and auxiliary
air to the brake cylinder. This may be continued until the auxiliary
reservoir and brake cylinder pressures become equal, after which any
further reduction of brake pipe pressure is only a waste of air. With
seventy pounds brake pipe pressure, and eight-inch piston travel, a
twenty-pound reduction will cause equalization at about fifty pounds.

[Illustration: Fig. 16. Lap Position.]

156. Q. Explain the operation of the triple valve in the release of the
brake.

A. To release the brakes and recharge the auxiliary reservoirs, air is
admitted through the brake valve to the brake pipe. This increase of
pressure on the brake pipe side of the triple valve piston 4 above that
on the other side causes the piston and slide valve to move back to
release position, which permits the air in the brake cylinder to flow to
the atmosphere, through the exhaust port of the triple, thus releasing
the brake. At the same time, air from the brake pipe flows through the
feed groove "i" around the triple piston to the auxiliary reservoir,
which is thus recharged. Now the "K" triple valve has two release
positions: =Full Release= and =Retarded Release=. To which of these two
positions the parts will move when the brakes are released, depends upon
how the brake pipe pressure is increased. It is generally understood
that those cars toward the head end of the train, receiving the air
first, will have their brake pipe pressure raised more rapidly than
those in the rear; thus the friction of the brake pipe causes the
pressure to build up more rapidly in the chamber "h" of the triple valve
toward the front end of the train than in those in the rear. As soon as
the pressure is enough greater than the auxiliary reservoir pressure to
overcome the friction of the piston, graduating valve and slide valve,
all three are moved toward the left until the piston stem strikes the
retarding stem 31, which is held in position by the retarding spring 33.
Where the rate of increase of brake pipe pressure is slow, it will be
impossible to raise the pressure in chamber "h" sufficiently to overcome
the tension of the retarding spring 33, and the triple valve will remain
in full release position, as shown in Fig. 13. Brake cylinder air will
now be free to exhaust through port "r", large cavity "n" in the slide
valve and port "p" leading to the atmosphere. If, however, the triple
valve is near the head end of the train, and the brake pipe pressure
builds up more rapidly than the auxiliary can recharge, an excess of
pressure will be obtained in chamber "h" over that in the auxiliary
reservoir, and will cause the piston 4 to compress the retarding spring
33, and move the triple valve parts to retarded release position as
shown in Fig. 17.

157. Q. What effect has retarded release position of the triple valve on
the release of the brakes?

A. In this position of the triple valve, cavity "n" in the slide valve
connects port "r" leading to the brake cylinder, with port "p" to the
atmosphere, and the brake will release; but as the small "tail port"
extension of cavity "n" is over exhaust port "p", the discharge of air
from the brake cylinder is quite slow.

[Illustration: Fig. 17. Retarded Release and Charging Position.]

158. Q. What is the object of delaying the exhaust of the brake cylinder
air?

A. In this way, the brakes on the front end of the train require a
longer time to release than those on the rear. This feature is called
=retarded release=, and although the triple valves near the locomotive
commence to release before those in the rear, yet the exhaust of air
from the brake cylinder is sufficiently slow to hold back the release of
the brakes at the front end of the train long enough to insure a uniform
release of the brakes on the train as a whole. This permits of releasing
the brakes on very long trains at low speeds without danger of damaging
train.

[Illustration: Fig. 18. Emergency Position.]

159. Q. What other desirable feature is found in this position of the
triple valve?

A. In this position, the back of the piston is in contact with the end
of the slide valve bush, and, as these two surfaces are ground to an
accurate fit, the piston makes a tight "seal" on the end of the bush
except at one point, where a feed groove is cut in the piston to allow
air to pass around the end of the slide valve bush into chamber "R" and
the auxiliary reservoir. This feed groove is much smaller than the feed
groove "i" in the piston bush, so that when the triple valve piston is
in =Retarded Release= position the recharge of the auxiliary reservoir
takes place much more slowly than when it is in =Full Release= position,
thus permitting a greater volume and pressure of air to flow toward the
rear of the train.

160. Q. Explain the operation of the triple valve in emergency position.

A. When any sudden reduction of brake pipe pressure is made below that
in the auxiliary reservoir, it will be felt in chamber "h" in front of
piston 4 and cause this piston to move to the extreme right, as shown in
Fig. 18. This movement of the parts will open port "t" in the slide
valve seat and allow air from the auxiliary reservoir to flow to the top
of the emergency piston 8, forcing the latter downward and opening
emergency valve 10. The unseating of the emergency valve allows the air
in chamber "Y" to escape to the brake cylinder, thus permitting brake
pipe pressure in chamber "a" to lift the check valve 15 and flow to the
brake cylinder through chambers "Y" and "X", until brake cylinder and
brake pipe pressure nearly equalize, when the check valve is forced to
its seat by the check valve spring 12, preventing the air in the
cylinder from escaping back into the brake pipe again. The emergency
valve and piston will now return to their normal position. At the same
time port "s" in the slide valve registers with port "r" in the slide
valve seat, and allows air from the auxiliary reservoir to flow to the
brake cylinder. This sudden discharge of brake pipe air into the brake
cylinder has the effect on the next triple valve, which in turn vents
brake pipe air that affects the following triple valve and so on
throughout the train.



NEW YORK AIR BRAKE

AIR COMPRESSOR


161. Q. What do Figures 19 and 20 represent?

A. These are cross-sectional views of the New York compressor.

162. Q. Of what does the valve gear of this compressor consist?

A. Of two main valves, actuated by tappet rods which enter into the
hollow piston rods, and are moved by tappet plates, which are fastened
to the steam piston heads.

163. Q. How is the admission and exhaust of steam controlled?

A. The valve under the cylinder at the right controls the flow of steam
to and from the cylinder at the left; while the valve under the cylinder
at the left controls the flow of steam to and from the cylinder at the
right.

164. Q. Explain the operation of the steam end of the compressor.

[Illustration: Low Pressure Piston Moving Upward. High
Pressure Piston at Rest. Fig. 19.]

A. Assuming both pistons are at the bottom of their cylinders, when the
compressor throttle is opened, live steam will flow to both steam chests
"B" (see Fig. 19), and through port "o" to the under side of the piston
"T" and through port "g" to the upper side of piston "H". The steam
under piston "T" will force it upward, and when it very nearly completes
its stroke, the tappet plate "Q" will engage the button on the end of
the tappet rod "P", moving the main valve "C" to its upper position. In
this position the exhaust cavity "r" in the main valve connects port "g"
with the exhaust port "X", thus allowing steam above the piston "H" to
escape to the exhaust, at the same time steam is admitted through port
"s" to the under side of piston "H", forcing it upward. As this piston
very nearly completes its stroke, the tappet plate "L" (see Fig. 20)
engages the button on the tappet rod "P", moving the main valve "A" to
its upper position. Exhaust cavity "r" now connects port "o", which
leads to the lower end of the cylinder at the right, with the exhaust
port "X", thus allowing the steam under piston "T" to escape to the
exhaust, at the same time steam is admitted through port "V" to the
upper end of the cylinder at the right, on top of piston "T", forcing it
downward; as it very nearly completes its stroke, the tappet plate "Q"
engages the shoulder on the tappet rod "P", moving the main valve "C" to
its lower position. The exhaust cavity "r" in the valve now connects
port "s" with the exhaust port "X", allowing steam below piston "H" to
escape to the exhaust, and at the same time steam is admitted to the top
of this piston, forcing it down, thus completing a cycle of the
compressor.

165. Q. Explain the operation of the air end of the compressor.

A. As the piston in the low pressure cylinder "D" moves up (see Fig.
19), a partial vacuum is formed below it, and air flowing through the
strainer passes downward through the air passage, then past the lower
receiving valve "W" into the lower end of the cylinder, filling it with
air at about atmospheric pressure. In the meantime the air that is being
compressed above the piston holds the receiving valve "U" to its seat,
and lifts the upper intermediate discharge valve "K" from its seat,
allowing the air to pass from the low to the high pressure cylinder "F".
The high pressure piston now moving up causes a partial vacuum to be
formed below it, and air from the atmosphere flows past the lower
receiving valve "N", filling this end of the cylinder with air at about
atmospheric pressure. The air above the piston being compressed, holds
the upper intermediate valve "K" and receiving valve "J" to their seats
and lifts the upper final discharge valve "M", allowing the air to pass
to the main reservoir. The action is the same on the down stroke, only
air is compressed in the opposite end of the cylinders and the opposite
air valves are used.

166. Q. What should be the lift of the different air valves?

A. In the No. 1 and No. 2 compressors all valves should have 1/16-inch
lift; in the No. 5 and No. 6 all valves should have 3/16-inch lift.

167. Q. If a receiving valve to the low pressure air cylinder breaks or
sticks open, what effect will it have on the compressor, and how may it
be located?

A. No air will be compressed in the low pressure cylinder, as the piston
moves toward the defective valve, and may be located by noting the
movement of the low pressure piston, as it will be much quicker toward
the defective valve than the opposite stroke. Air will blow back to the
atmosphere as the piston moves toward the defective valve, and may be
detected by holding the hand over the strainer.

168. Q. If an intermediate discharge valve breaks or sticks open, what
effect will it have on the compressor, and how may it be located?

A. If an intermediate discharge valve breaks or sticks open, no air will
be compressed by that end of the compressor where is located the
defective valve, as the air will simply flow back and forth from the
high to the low pressure cylinders; no air will be taken in from the
atmosphere through the strainer as the pistons move from the defective
valve.

169. Q. If a final discharge valve breaks, what effect will it have on
the compressor?

A. Main reservoir air will be free to return to the high pressure
cylinder as the high pressure piston moves from the defective valve;
therefore, no air will be taken in through the receiving valve of the
high pressure air cylinder at the end where is located the defective
valve. The low pressure piston will make a slow stroke toward the
defective valve and a normal stroke from it; while the high pressure
piston will make a slow stroke toward the defective valve and a quick
stroke from it. Defective air valves may generally be located by noting
the temperature of the valve chamber in which they are located.

170. Q. What will cause the compressor to run hot?

A. Running the compressor too fast; working against high pressure; air
piston packing rings leaking; air cylinder worn; air passages or
discharge pipe partially stopped up; air valves leaking; air valves
stuck shut; or lack of lubrication.

171. Q. How should the air end of the compressor be oiled, and what
grade of oil used?

[Illustration: Fig. 20. High Pressureiston Moving Upward. Low
Pressure Piston at Rest.]

A. Oil should be used sparingly in the low pressure cylinder, but more
is required in the high pressure cylinder, owing to higher temperature.
A good quality of valve oil should be used.

172. Q. How is the steam end of the compressor affected by the use of
too much oil?

A. This may cause the compressor to short stroke, and where the piston
type of valve is used, may cause the compressor to stop.



L-T EQUIPMENT

AUTOMATIC CONTROL VALVE


173. Q. What is the duty of the control valve?

A. To admit air from the main reservoir to the locomotive brake
cylinders when applying the brakes; to automatically maintain the brake
cylinder pressure against leakage; to develop the proper brake cylinder
pressure regardless of piston travel; and to exhaust the air from the
brake cylinders when releasing the brake, in all automatic applications
of the brake.

174. Q. Explain the operation of the control valve when making an
automatic service application of the brake.

A. Air enters the control valve at the connection marked "BP" (Fig. 21),
which leads to chamber "F" above the piston 3, forcing it down,
uncovering the feed groove "G" in the bushing, allowing air to feed past
the piston into the slide valve chamber, and then through port "H" to
the auxiliary reservoir. The air will feed through in this manner until
the auxiliary reservoir and brake pipe pressure equalize. When a gradual
reduction of brake pipe pressure is made, it will be felt in chamber
"F", above piston 3, creating a difference in pressure on the two sides
of the piston, which will cause it to move upward.

[Illustration: Fig. 21. Automatic Control Valve. Full Release.]

The first movement of the piston closes the feed groove "G", also moves
the graduating valve 10, uncovering the service port "J" in the slide
valve 4, and the continued movement of the piston moves the slide valve
to service position, in which the service port "J" connects with port
"E" in the valve seat. (See Fig. 22.) As the slide valve chamber and
auxiliary reservoir are connected at all times, air can now flow from
the auxiliary to the control cylinder "D" and control reservoir, through
ports "H", "J" and "E", until the pressure on the lower or auxiliary
side of piston 3 becomes slightly less than that in chamber "F" or brake
pipe side, when the piston and graduating valve will move down until the
shoulder on the piston strikes the slide valve; this movement of the
graduating valve closes the service port "J", thus closing the
communication between the auxiliary and control cylinder and reservoir,
also closing port "W", which leads to the safety valve. (See Fig. 23.)

175. Q. How is piston 2 affected by the air pressure in the control
cylinder "D"?

A. Pressure forming in this cylinder will force the piston downward. The
piston in moving down will carry the exhaust valve 7 with it, closing
the exhaust port "N" and moves the preliminary admission valve "1A" from
its seat against the tension of spring 8, allowing the pressure in
chamber "O" to pass to the brake cylinders, thus creating a balancing
effect on valve 1, which allows it to be opened against main reservoir
pressure, thus allowing main reservoir air to flow from chamber "A" to
chamber "B" and the brake cylinders on the locomotive (see Fig. 22)
until the pressure in the brake cylinders and chamber "B", below piston
2, becomes slightly greater than that in the control cylinder "D" when
the piston will move up just far enough to allow the valves "1" and
"1A" to be seated, or to lap position. (See Fig. 23.)

[Illustration: Automatic Control Valve. Service Position. Fig. 22.]

176. Q. With the control valve now in lap position, will the brake
release on account of brake cylinder leakage?

A. Any drop in brake cylinder pressure will be felt in chamber "B" below
the piston 2, causing a difference in pressure on the two sides of the
piston, allowing the pressure in the control cylinder "D" to move the
piston 2 down, unseating the admission valves, allowing a further flow
of main reservoir air from chamber "A" to chamber "B" and the brake
cylinders until the pressure is again slightly greater than that in the
control cylinder "D", when the piston 2 will again move up, allowing the
admission valves to close. Thus in this way air will be supplied to the
brake cylinders of the locomotive, holding the brakes applied regardless
of leakage.

177. Q. Explain the movement of the parts in the control valve, when the
automatic brake valve is moved to release position, following an
automatic application of the brake.

A. In release position of the brake valve, air from the main reservoir
flows direct to the brake pipe, causing an increase of pressure, which
is felt in chamber "F" on the upper side of piston 3; this increase of
pressure will cause the piston to move down, carrying with it the
graduating valve 10 and slide valve 4 to release position. This allows
air from the control cylinder "D" and control reservoir to flow through
the release pipe "IV" and on to the automatic brake valve, where the
port to which this pipe leads is blanked by the automatic rotary valve,
which prevents the air leaving the control cylinder and reservoir, thus
holding the locomotive brake applied while the train brakes are being
released. The movement of the parts are the same where the release is
made in holding position.

178. Q. Explain the movements of the parts in the control valve when the
automatic brake valve is moved to running position, after having first
been moved to release or holding position.

[Illustration: Automatic Control Valve. Service Lap Position. Fig. 23.]

A. In this position of the brake valve the port to which the release
pipe "IV" is connected is open to the exhaust, thus allowing the air in
the control cylinder and reservoir to escape to the atmosphere. The
reduction of pressure in the control cylinder "D" below that in chamber
"B" causes the control piston 2 to move up, carrying with it the exhaust
valve 7 to release position, opening the exhaust port "N", thus allowing
the air to return from the brake cylinders through ports "C" and "N" to
the atmosphere, releasing the brake. (See Fig. 21.)

179. Q. Explain what takes place in the control valve when an automatic
emergency application of the brake is made.

A. Any sudden reduction of brake pipe pressure will be felt on the brake
pipe side of piston 3, and will cause it and the valve 4 to move to
their extreme upper position, the knob on the piston striking the
graduating stem 13, causing it to compress the spring 14, moving the
emergency valve 15 upward, opening port "Q"; this allows brake pipe air
to flow against valve 16, unseating it, then through port "T" to the
brake cylinder. (See Fig. 24.) In the meantime auxiliary reservoir air
can flow past the end of the slide valve through port "E" to the control
cylinder "D" and control reservoir, forcing piston 2 downward unseating
valves "I" and "IA", thus allowing main reservoir air to flow to the
brake cylinders, applying the brake.

180. Q. At what pressure will the auxiliary reservoir and control
reservoir equalize when using seventy pounds brake pipe pressure?

A. At about fifty pounds; however, with the automatic brake valve in
emergency position, there is a small port in the rotary valve (called
the blow-down timing port) opened to the control reservoir pipe and
control reservoir which allows main reservoir air to flow to the control
reservoir and cylinder, raising the pressure to the adjustment of the
safety valve.

[Illustration: Fig. 24. Automatic Control Valve. Emergency Position.
(With Quick Action Cylinder Cap.)]

181. Q. At what pressure is the safety valve adjusted?

A. At fifty pounds.

182. Q. What types of brake valve are used with this equipment?

A. The automatic brake valve is of the rotary valve type and is the same
valve as used with the E-T equipment. The straight air brake valve is of
the slide valve type. The control valve takes no part in the application
or release of the straight air brake. What has been said of the H-6
brake valve used with the E-T equipment, applies to the automatic brake
valve used with the L-T equipment.



BROKEN PIPES


183. Q. If the main reservoir supply pipe to the automatic control valve
breaks, what should be done?

A. Plug the pipe toward the main reservoir. The locomotive brake cannot
be applied in an automatic service application; but if the control valve
be equipped with a quick action cap and an emergency application is
made, the air vented from the brake pipe to the brake cylinder will
apply the brake. The independent brake will not be affected.

184. Q. What will be the effect if the release pipe breaks?

A. The holding feature of the brake will be lost; that is, the brake
will release when the automatic brake valve is returned to release or
holding position.

185. Q. If the brake cylinder pipe breaks, can the locomotive brake be
applied with the automatic brake valve? With the independent brake
valve?

A. This depends on where the pipe breaks; if between the cut-out cock
and any one of the brake cylinders, close the cut-out cock to that
cylinder, and the other cylinders may be used. But if the pipe breaks
between the control valve and the double-throw check valve, the
automatic brake is lost; if the break be between the independent brake
valve and double-throw check valve, the independent brake is lost.

186. Q. If the brake cylinder pipe breaks and is not plugged, what must
be done?

A. Close the cut-out cock in the main reservoir supply pipe, this to
avoid the waste of air when a brake application is made on the train.

187. Q. If the brake pipe connection to the control valve breaks, what
should be done?

A. Plug the end leading from the brake pipe; the automatic brake cannot
be applied on the locomotive, but the independent brake will not be
affected.

188. Q. If the control cylinder pipe breaks, what effect will it have
and what must be done?

A. The locomotive brake cannot be applied with the automatic brake
valve; by plugging the pipe, this feature of the brake will be restored,
but the independent release feature will be lost.

189. Q. If any of the pipes here enumerated breaks, will it in any way
affect an application of the independent brake?

A. No; as the independent and automatic features are entirely separate
from each other; that is, the automatic control valve is not brought
into use when an independent application of the brake is made.



CONTROL VALVE DEFECTS


190. Q. If there is a blow at the control valve exhaust port when the
brake is released, where would you look for the trouble?

A. This would indicate a leaky application valve, or a leak past the
emergency valve.

191. Q. If there be a continuous blow at the control valve exhaust port
when the brake is applied, where would you look for the trouble?

A. This would indicate leakage past the exhaust valve 7.

192. Q. If the locomotive brake released with the automatic brake valve
in lap position, where is the trouble?

A. Would look for a leak in the control reservoir pipe or special
release valve.

193. Q. If the brake remained applied in lap position, but released in
release or holding position, where would you look for the trouble?

A. This would indicate a leak in the control valve release pipe.



MISCELLANEOUS


194. Q. What is meant by an application of the brake?

A. The first and all following reductions, until the brake is released.

195. Q. How many applications of the brake should be made when making a
stop with a passenger train, and why?

A. Two; the first a heavy one to reduce the speed quickly, and the
second a light one to complete the stop; thereby preventing wheel
sliding and shock to the train.

196. Q. How many applications of the brake should be made when making a
stop with a long freight train?

A. One; this to prevent the possibility of causing damage to the train.

197. Q. Explain how a stop should be made with a freight train.

A. Probably no more difficult question to answer could be asked, as the
service braking of a train must be governed by the condition surrounding
it; meaning, relation of brake power to weight of train; rail condition;
speed and grade. To prevent breaking in two and other damage, freight
trains should be stopped with one brake application, which may consist
of one or more reductions, up to full service. Generally speaking, the
slack should be bunched before the brakes are applied, and this may best
be done by gradually closing the throttle and allow the train to drift
some little distance. The first reduction should not be less than five
or more than eight pounds. The brakes should be applied as soon as
possible after the slack has had time to run in, the object of this
being to have the train slack adjusted while the brakes are least
effective, due to the high speed and light brake cylinder pressure. It
is at this time that damage may be done to the train; therefore, if the
slack be kept bunched or stretched, as the case may be, the possibility
of train damage will be greatly reduced. To obtain this condition,
complete the stop with as light a brake application as permissible. When
the brake is first applied, the engineer should note if the tendency be
for the train slack to bunch or stretch, and having learned that the
train is inclined to stretch badly, he can keep the slack stretched by
making the initial brake pipe reduction before shutting off steam, then
shut off steam gradually as soon as the brake valve exhaust port closes,
the object in working steam being to prevent the slack running in as the
application is made, which in turn will prevent severe jerks due to the
slack running out as the rear brakes become effective. Where the
locomotive is equipped with an independent release feature, its brakes
should be kept released while the train brakes are being applied.

198. Q. Is it considered good practice to attempt making an accurate
stop with a freight train?

A. It may be said to be very poor judgment to attempt making an accurate
stop with a freight train, such as a spot stop for coal or water or a
close-up stop for a switch. Some engineers seem to think that it is a
reflection on their judgment if an accurate stop is not made, but this
is not so, due to the fact that no two trains brake alike, and the same
train may not brake twice alike. Therefore, aim for a smooth stop, which
means a safe stop, leaving accuracy out of the question until the time
comes when you are handling a passenger train.

199. Q. What precaution should be taken after a stop is made on a heavy
grade?

A. The air brakes should be released and a sufficient number of hand
brakes applied to hold the train. Never rely on the air brake to hold
the train for any length of time.

200. Q. Why is it dangerous to repeatedly apply and release the brakes
without giving time for the auxiliaries to fully recharge?

A. As time is required to charge the auxiliaries, the feed groove in the
triple valve being small, if the brakes are repeatedly applied and
released without giving time to recharge, the braking power will be
lost.

201. Q. What benefits are derived from the use of the retaining valve?

A. By use of the retaining valve the brake is held applied while the
triple valve is in release position and the auxiliary is being
recharged; thereby assisting in retarding the movement of the train down
grade, also keeps the train bunched and gives a higher brake power on
the second application with the same reduction of brake pipe pressure.

202. Q. With a seventy-pound brake pipe pressure how much of a reduction
is necessary to set the brakes in full, and why?

A. About twenty pounds. This will cause the auxiliary reservoir and
brake cylinder pressures to equalize.

203. Q. What effect has piston travel on the pressure developed in the
brake cylinder?

A. The longer the piston travel the greater the volume or space to be
filled with air; therefore the lower the pressure.

204. Q. When should brakes be tested?

A. Brakes should be tested before leaving a terminal and after any
change in the make-up of the train, at all designated points, also,
whenever the engineer is in doubt as to his having the control of all
brakes.

205. Q. How should a terminal test of the brakes be made?

A. After the pressure is pumped up, a reduction of about ten pounds
should be made and the length and force of the brake pipe exhaust should
be noted, also the manner in which the exhaust closes; then a further
reduction of ten pounds should be made and the brake held applied until
signaled to release.

206. Q. If, when making a service application of the brake, the brake
pipe exhaust closes suddenly and then begins to blow again, what does it
indicate?

A. That the brakes, or at least part of them, have applied in quick
action.

207. Q. What is meant by a running test, and when should this test be
made?

A. A running test is made while the train is in motion, and steam is
being used, when a sufficient reduction should be made to apply all
brakes. After noting the efficiency of the brakes they should be
released. Running tests should be made following all standing tests and
at all other points on the road as required by the rules.

208. Q. When double-heading, which engineman should have full control of
the brakes?

A. The head engineer; the cut-out cock under the brake valve on the
second engine should be closed and the compressor allowed to run.

209. Q. How may the engineman assist the trainman in finding a bursted
hose?

A. After the train has come to a stop, the brake valve should be placed
in running position; by so doing, air will be admitted to the brake pipe
and cause a blow at the point where the hose is burst.

210. Q. If the locomotive brake creeps on with the automatic and
independent brake valves in running position, where would you look for
the trouble?

A. This is caused by the pressure chamber being overcharged or a
non-sensitive feed valve allowing brake pipe pressure to vary, which in
turn causes an automatic application of the brake.

211. Q. How often should the main reservoir be drained?

A. The main reservoir should be drained at the beginning of each trip.


       *       *       *       *       *


=INDEX=
                                                          Page

Air Brake Questions, First Series                           22
Air Brake Questions, Second Series                          44
Air Brake Questions, Third Series                          164
Compound Locomotives                                        98
Examination Questions, First Series                          7
Examination Questions, Second Series                        25
Examination Questions, Third Series, Mechanical             62
Federal Regulations                                        126
Headlight, Pyle National                                   127
Headlight, Schroeder                                       141
Headlight, "Buda-Ross" Electric                            143
Lubrication                                                120
Oil Burning Locomotives                                     47
Preface                                                      3
Southern Valve Gear                                        119
Stoker, Duplex                                             154
Walschaert and Baker-Pilliod Valve Gears                   113

       *       *       *       *       *

Transcribers Notes:

Punctuation and heading format normal.

Page 7, "feul" changed to "fuel" (use of fuel).
Page 16, "therby" changed to "thereby" (thereby causing)
Page 31, "criculation" changed to "circulation" (good circulation)
Page 65, "lcomotive" changed to "locomotive" (locomotive has been started)
Page 78, "reevrse" changed to "reverse" (reverse lever)
Page 86, "serously" changed to "seriously" (very seriously affect)
Page 108, "disadvanage" changed to "disadvantage" (disadvantage to work)
Page 126, "aperating" changed to "operating" (operating under the laws)
Page 129, "sucessfully" changed to "successfully" (used successfully)
Page 131, "damge" changed to "damage" (might do damage)
Page 139, "Tubo" changed to "Turbo" (Turbo-generator)
Page 147, "direcion" changed to "direction" (in any direction)
Page 149, "cummutator" changed to "commutator" (The commutator)
Page 204, "distributng" changed to "distributing" (distributing valve)
Page 215, "chambr" changed to "chamber" (remaining in chamber)
Page 216, "slighty" changed to "slightly" (slightly less)
Page 233, "releas" changed to "release" (release is made)
Page 243, "the" changed to "then" (and then begins to blow).





*** End of this LibraryBlog Digital Book "The Traveling Engineers' Association - To Improve The Locomotive Engine Service of American Railroads" ***

Copyright 2023 LibraryBlog. All rights reserved.



Home